cmeng48
Q: can i use to regulate the speed of a dc motor?
gevraagd door BG375415825 op 2022-05-28 07:37:16
cmeng48 As long as your motor is less than 2000 watt.. it should work but talk to your electrician for proper advice. Personally this is an open item and could be dangerous if not housed properly.
2022-05-28 06:15:25 Nuttig (0)
BG549021181 I think it should be Stainless Steel
2021-03-02 09:43:10 Nuttig (8)Q: Does this kit fit the rear master cylinder of a 2005 harley 883?
gevraagd door Lucio op 2021-03-24 05:58:28
cmeng48 No.
2021-10-13 07:42:06 Nuttig (0)Q: hi! is this item can be use for electric drill?
gevraagd door zack op 2020-09-23 03:24:37
cmeng48 no.
2021-10-13 07:41:48 Nuttig (0)Q: Can it be used on mild steel?
gevraagd door viking61 op 2021-10-12 08:30:37
cmeng48 Hi viking61, I am a machinist long time ..No it cannot be used on mild steel they are dissimilar metals. For mild steel use silver brazing rod with at least 40% silver and a brazing flux for a strong joint or repair. Hope this helps.
2021-10-12 08:38:50 Nuttig (1)Q: Is the Dremel 3000 compatible?
gevraagd door weyselkalkan op 2021-07-09 05:19:28
cmeng48 What do you mean?.. if you are asking if the dremel tool is to be used as a tool for gear cutting then no! Gear cutting requires a lot of experience in machining and a lot of machine tools. I hope this helps.
2021-07-09 05:43:29 Nuttig (1)Q: Is it solar energy dependent? will it work at night?
gevraagd door GKM op 2019-12-20 01:59:28
cmeng48 Itshould work at night but not sure cause I don't weld at night.
2021-05-15 01:01:07 Nuttig (0)Q: When would a Module 1 PA20 Bore 22mm "5" HSS Involute Gear Milling Cutter be available. thanks.
gevraagd door BG445191415 op 2021-05-14 08:25:34
cmeng48 Iam only a buyer..so I don't know. Try Aliexpress.com if you are in a hurry.
2021-05-15 12:59:55 Nuttig (0)
cmeng48 yesready to cut.
2021-05-15 12:58:40 Nuttig (0)Q: Can i use this in my guitar as a killswitch? is it normally opened or normally closed one?
gevraagd door Arkonil op 2019-08-26 06:19:28
cmeng48 Nodon't think so!
2021-05-05 06:15:19 Nuttig (0)
cmeng48 Thickness is 1.6mm 1-16'' of an inch.. Length of rod is 500mm or about 20 inches. They have flux in between rod so you don't have to use flux.
2021-03-20 05:49:04 Nuttig (0)
Q: does this phone have 802.11ac wifi. as it says in the description.
gevraagd door BG364611155 op 2021-02-27 11:15:21
cmeng48 Sure does!
2021-02-28 02:08:33 Nuttig (2)Q: good for Al an copper combined?
gevraagd door Cusniriuc op 2020-02-22 03:20:02
cmeng48 No.
2021-02-18 04:44:31 Nuttig (0)We nodigen je van harte uit om je te abonneren op de Invite Answer-e-mail!
Als u zich abonneert, nodigen we u uit via e-mail om vragen te beantwoorden die mensen hebben over producten. Door je te abonneren, verdien je ook de "Behulpzame Badge "! U kunt zich op elk moment uitschrijven op de pagina met privacyinstellingen.
Help anderen en wees gelukkiger!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
cmeng48 Yesit can be used for aluminum..all carbide end mills can.
2022-08-12 09:34:38 Nuttig (0)