Alle berichten

Q: Is this tinned pure copper or is it CCA wire?

gevraagd door BG225733103 op 2022-10-04 12:13:40

Burplerlcbm tinned copper

2022-10-05 08:22:57 Nuttig (0)
Verzenden
antwoorden (1)

Q: What is RTC for each tip?

gevraagd door BG143912477 op 2022-03-19 01:31:58

BG225733103 RTC? Wich definition of RTC are you talking about? Your Question makes no sense...There are lots of different meanings for RTC. See here: en.wikipedia.org | wiki | RTC If you want people to help you stop using acronyms and give more context instead of just a short question.

2022-03-19 04:06:24 Nuttig (0)
Verzenden
antwoorden (2)

BG225733103 Sure looks like a scalpell blade to me. The blade shown here seems to be for use with a scalpell handle no 3 or 4. Blade shape could be a Rüttgers no 11 or an Aesculap no 25. But the mounting slot is the same for all blade shapes, so you can use any shape you like. Use your favorite image search engine to search for "scalpell blade shapes" to find the one you want.

2021-09-16 03:45:51 Nuttig (1)
Verzenden
antwoorden (2)

Q: What kinds of probes/leads should I use?

gevraagd door cubeconvict op 2019-06-27 10:47:07

BG225733103 Bare wire is probably best. I suspect that it was never intended for banana plugs, but as pure screw terminals. Hole diameter in the plastic head is about 5.5mm.

2021-08-29 01:06:26 Nuttig (0)
Verzenden
antwoorden (6)

Q: what kind of fuses use? 5x20 mm? and how much amperes are each one?

gevraagd door pjlabarta op 2019-09-29 08:59:13

BG225733103 I suspect that the fuses that are currently present will be installed with respect to the current. My board contained 5A fuses.

2021-08-29 12:57:48 Nuttig (0)
Verzenden
antwoorden (6)

Q: Can I get 24V by connection with 12V and -12V?

gevraagd door BG405471057 op 2021-08-22 02:03:19

BG225733103 On the board is no circuitry that would prevent you from using the +12V with the -12V instead of GND - the screw terminals are connected straight to the ATX connector via a fuse only. So yes, you __could__ get a 24V potential. If it works or if it goes bang depends entirely on the ATX PSU that you connect to the board.

2021-08-29 12:50:15 Nuttig (0)
Verzenden
antwoorden (8)

Q: Are their 220 Ohm and 10 k values resistors?

gevraagd door BG019391538 op 2021-08-03 04:09:34

BG225733103 all Ω values are listed in the overview.

2021-08-03 10:36:45 Nuttig (1)
Verzenden
antwoorden (9)

Q: do you have 1k resistors included

gevraagd door BG153723470 op 2020-11-06 07:54:55

BG225733103 1kΩ is listed in the value list shown in the overview, so yes there are 20 pieces.

2021-08-03 10:33:15 Nuttig (0)
Verzenden
antwoorden (2)

Q: How much current does it draw?

gevraagd door BG225733103 op 2021-06-22 07:09:26

Joao 12v

2021-07-14 09:58:55 Nuttig (0)
Verzenden
antwoorden (1)

BG225733103 So...Where are the pictures of the grown plants? It's been 22 months...

jrgunder 17/08/2019
0
Reacties (1)

BG225733103 Inthe description it says 3mm. Measured with a caliper the shanks are between 3,09mm and 3.16mm

2021-05-25 06:21:04 Nuttig (0)
Verzenden
antwoorden (2)

BG225733103 Isthe LED indicating power on? If yes, make sure the 5A fuses aren't blown.

2021-05-25 06:16:21 Nuttig (0)
Verzenden
antwoorden (8)