T2401-O T2401-N DC 12V Dubbele LED Display Tijd Relais Module Digitale Tijd Vertraging Relais Cyclus Timer Schakel Controle Module Actieve/Passieve Uitgang Beoordelingen

T2401-O T2401-N DC 12V Dubbele LED Display Tijd Relais Module Digitale Tijd Vertraging Relais Cyclus Timer Schakel Controle Module Actieve/Passieve Uitgang

US$6.99
~~US$9.65~~
Nu kopen

Klantbeoordelingen

4.87 van5

Bekijk alle beoordelingen van15

Schrijf een beoordeling Ontvang dubbele banggoodpunten als je één van de 3 eerste beoordelingen plaatst!

Alle beoordelingen(15)
Afbeeldingen
Videos
Ster
- Ster(15)
- 5 Ster(14)
- 4 Ster(0)
- 3 Ster(1)
- 2 Ster(0)
- 1 Ster(0)

Sorteren op:

Top recensie

Top recensie
Meest nuttig
meest recent

Recensies alleen uit uw land (United States)

Toon origineel

Een deel van de recensie is automatisch vertaald.

GombiVIP2
HU
24/04/2023

Köszönöm szépen. Nagyon jó termék. Remekül működik! Teszi a dolgát. 😉😊👍

Köszönöm szépen. Nagyon jó termék. Remekül működik! Teszi a dolgát. 😉😊👍

Köszönöm szépen. Nagyon jó termék. Remekül működik! Teszi a dolgát. 😉😊👍
0

Reacties

Toon origineel
Craig_MarkVIP2
US
15/06/2024

Works very well, the set-up instruction are a little confusing - below are my notes to make it easier Press and hold “S” for six seconds to enter “Setup” Press “S” to change “MODE” (P0, P1, P2 or P3) Press “up/down arrow” to change Code value Double press “S” to change count down time value P0 = Countdown timer to turn “Off” power (Green) Second line (Code Value) 0 = Seconds 1 = Minutes 2 = Hours P1 = Countdown timer to turn power “ON” (Red) Second line (Code Value) 0 = Seconds 1 = Minutes 2 = Hours P2 = Power Failure Default Second line On Off P3 = Lock setting Second line 0 = un locked 1 = Locked Hope that helps

Works very well, the set-up instruction are a little confusing - below are my notes to make it easier Press and hold “S” for six seconds to enter “Setup” Press “S” to change “MODE” (P0, P1, P2 or P3) Press “up/down arrow” to change Code value Double press “S” to change count down time value P0 = Countdown timer to turn “Off” power (Green) Second line (Code Value) 0 = Seconds 1 = Minutes 2 = Hours P1 = Countdown timer to turn power “ON” (Red) Second line (Code Value) 0 = Seconds 1 = Minutes 2 = Hours P2 = Power Failure Default Second line On Off P3 = Lock setting Second line 0 = un locked 1 = Locked Hope that helps

Works very well, the set-up instruction are a little confusing - below are my notes to make it easier Press and hold “S” for six seconds to enter “Setup” Press “S” to change “MODE” (P0, P1, P2 or P3) Press “up/down arrow” to change Code value Double press “S” to change count down time value P0 = Countdown timer to turn “Off” power (Green) Second line (Code Value) 0 = Seconds 1 = Minutes 2 = Hours P1 = Countdown timer to turn power “ON” (Red) Second line (Code Value) 0 = Seconds 1 = Minutes 2 = Hours P2 = Power Failure Default Second line On Off P3 = Lock setting Second line 0 = un locked 1 = Locked Hope that helps
2

Reacties

Toon origineel