PTFE gecoate motor loodschroef T8 Lood 2/8mm pitch 2mm POM moer voor Ender-3 Serie/CR-10 Serie/Sidewinder 3D-printer onderdeel Beoordelingen - Banggood Nederlands Online winkelen

PTFE gecoate motor loodschroef T8 Lood 2/8mm pitch 2mm POM moer voor Ender-3 Serie/CR-10 Serie/Sidewinder 3D-printer onderdeel

6,21€
~~21,42€~~
Nu kopen

Klantbeoordelingen

5 van5

Bekijk alle beoordelingen van5

5 ster
5 (100.0%)
4 ster
0 (0%)
3 ster
0 (0%)
2 ster
0 (0%)
1 ster
0 (0%)

Schrijf een beoordeling Ontvang dubbele banggoodpunten als je één van de 3 eerste beoordelingen plaatst!

Alle beoordelingen(5)
Afbeeldingen
Videos
Ster
- Ster(5)
- 5 Ster(5)
- 4 Ster(0)
- 3 Ster(0)
- 2 Ster(0)
- 1 Ster(0)

Sorteren op:

Top recensie

Top recensie
Meest nuttig
meest recent

Recensies alleen uit uw land (United States)

|

Toon origineel

Een deel van de recensie is automatisch vertaald.

Nachiket MhatreVIP3
IN
07/11/2021

Please don't waste your time on these. The machining quality of the lead screw is appalling, with uneven pitch all round. This is evident through cyclic binding with the lead screw nut. This problem was evident in both pairs of lead screws and nuts I had purchased, so this isn't mere coincidence. In fact, other nuts also bind on these lead screws, whereas the supplied nuts don't bind with other lead screws. If you buy these lead screws and install in your printer, that axis will experience massive binding and wobble. You are going to hurt both quality and durability of your 3D printer by using this product. Avoid this like the plague.

Please don't waste your time on these. The machining quality of the lead screw is appalling, with uneven pitch all round. This is evident through cyclic binding with the lead screw nut. This problem was evident in both pairs of lead screws and nuts I had purchased, so this isn't mere coincidence. In fact, other nuts also bind on these lead screws, whereas the supplied nuts don't bind with other lead screws. If you buy these lead screws and install in your printer, that axis will experience massive binding and wobble. You are going to hurt both quality and durability of your 3D printer by using this product. Avoid this like the plague.

Please don't waste your time on these. The machining quality of the lead screw is appalling, with uneven pitch all round. This is evident through cyclic binding with the lead screw nut. This problem was evident in both pairs of lead screws and nuts I had purchased, so this isn't mere coincidence. In fact, other nuts also bind on these lead screws, whereas the supplied nuts don't bind with other lead screws. If you buy these lead screws and install in your printer, that axis will experience massive binding and wobble. You are going to hurt both quality and durability of your 3D printer by using this product. Avoid this like the plague.
2

Reacties

Toon origineel
MadarMVIP3
HU
13/05/2021

Everything was OK!

Everything was OK!

Everything was OK!
0

Reacties

Toon origineel
mkubatVIP5
BA
18/10/2021

okk

okk

okk
0

Reacties

Toon origineel
mkubatVIP5
BA
20/09/2021

Videcemo

Videcemo

Videcemo
0

Reacties

Toon origineel
blake2244VIP2
US
29/04/2021

very nice. great upgrade and and they look good too!

very nice. great upgrade and and they look good too!

very nice. great upgrade and and they look good too!
0

Reacties

Toon origineel

Show:

Totaal 0 Pagina's

Ga naar pagina

Gaan

Wellicht ben je ook geïnteresseerd in

recommendation for you