Klantbeoordelingen

Schrijf een beoordeling
  • Alle beoordelingen(9)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(9)
    • 5 Ster(9)
    • 4 Ster(0)
    • 3 Ster(0)
    • 2 Ster(0)
    • 1 Ster(0)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (United States)
|
Toon origineel

Een deel van de recensie is automatisch vertaald.

  • 15/08/2020

    Product arrived well before due date, looks great, hot end of pen is removable with one screw and uses contact pins so comes apart for cleaning very easily. 2 amp power draw means you can use this on a decent powerbank with at least 2A output and be mobile. Great addition to my FDM 3D printer allowing me to tidy up small mistakes or weld components together and it uses the same 1.75mm width filament so I wont be running out of plastic to use any time soon. Have tried with ABS, PLA and Taulmann PETT, Pen has a max temp of 230 deg C which it will hit very quickly. Instructions are a bit patchy for the English version but mixing a few button presses I soon had it figured out, (hold feed and tap - button to adjust feed rate, tap both + & - to switch between abs and pla presets, hold - to activate manual temp mode and change in 1 deg increments with + & - ) Screen is very clear and easy to read. Motor is a compact one so it can be heard whining when in use and should not be forced to load or retract filament as it may be the first point of failure, can sometimes hear it slowing down when in use so the feed rate isn't quite as uniform as I would like but is still good enough for most situations. I suspect this would be a great mobile repair tool for people who break their cosplays at events and need a quick fix. Great Value, looks great, not bulky, very sleek and easy to hold.

    Reacties
    Toon origineel
  • 12/05/2021

    جميل

    Reacties
    Toon origineel
  • 10/05/2021

    Took some time to realise how it works since i didn't find any pdf except chinese.

    Reacties
    Toon origineel
  • 25/02/2021

    Works fine

    Reacties
    Toon origineel
  • 01/02/2021

    I purchased this pen so that I could join 3d printed parts. It works beautifully with PETG, so I am assuming it will work well with PLA too. Joined the parts very strongly ... great tool!

    Reacties
    Toon origineel
  • 27/01/2021

    Penna arrivata in 13 giorni, velocissimo. E' arrivata con l'adattatore per l'Italia ed un caricabatterie da 2A quindi funziona benissimo con qualunque caricabatterie per cell. In metallo, con il cappuccio in metallo, necessario quando si termina l'utilizzo per coprire la punta che, ovviamente scotta. Ha 6 velocità ed alla massima velocità l'estrusione è molto rapida, la velocità 3 è l'ideale. Molto facile da usare ma bisogna prenderci la mano. Consigliatissima.

    Reacties
    Toon origineel
  • 24/01/2021

    nice pen

    Reacties
    Toon origineel
  • 20/01/2021

    Ottima e di facile utilizzo

    Reacties
    Toon origineel
  • 02/01/2021

    Szuper! Hozza amit tudnia kell. Átalakítót küldtek hozzá, de én inkább 5V 2A-s EU aljzattal használom. Angol természetesen a használati utasítás, de az ember idővel kitapasztalja.

    Reacties
    Toon origineel
Show:

    Totaal 0 Pagina's

    Ga naar pagina

    recommendation for you
    • US$51.99
    • US$7.59
    • US$9.99
    • US$35.00
    • US$429.00
    • US$9.99
    • US$12.99
    • US$21.99
    • US$12.99
    • US$2.00
    • US$0.71
    • US$37.99
    • US$198.99