Pictures with the shield removed. I can't measure the power with this thing, but I expect it to be over the EU limited less than 100mW (20dBm) of the RC transmitters. According to other people is capable of 200mW? It will not work (led will not go blue) unless the input antenna is connected to an input source. The marking on the chip is scrapped, but I believe is a SE2576L chip by Skyworks Solutions. Details about this chip here: http://www.skyworksinc.com/Product/953/SE2576L XQ-02A is a bi-directional signal amplifier module designed for the 2.4GHz band. Features automatic direction (send or receive) identification and switching. According to schematics, maximum output peak power is 2W, but I assume this is not the case of the current PCB. Maybe the voltages must be adjusted, judging by other reports this is doing about 200mW maybe? In my quick testing, connected directly to the TX, the chip is not getting hot, barely warm, so not sure if I need to do something else or the low temperature is maybe of the reduced power output.

Pictures with the shield removed. I can't measure the power with this thing, but I expect it to be over the EU limited less than 100mW (20dBm) of the RC transmitters. According to other people is capable of 200mW? It will not work (led will not go blue) unless the input antenna is connected to an input source. The marking on the chip is scrapped, but I believe is a SE2576L chip by Skyworks Solutions. Details about this chip here: http://www.skyworksinc.com/Product/953/SE2576L XQ-02A is a bi-directional signal amplifier module designed for the 2.4GHz band. Features automatic direction (send or receive) identification and switching. According to schematics, maximum output peak power is 2W, but I assume this is not the case of the current PCB. Maybe the voltages must be adjusted, judging by other reports this is doing about 200mW maybe? In my quick testing, connected directly to the TX, the chip is not getting hot, barely warm, so not sure if I need to do something else or the low temperature is maybe of the reduced power output.

Pictures with the shield removed. I can't measure the power with this thing, but I expect it to be over the EU limited less than 100mW (20dBm) of the RC transmitters. According to other people is capable of 200mW? It will not work (led will not go blue) unless the input antenna is connected to an input source. The marking on the chip is scrapped, but I believe is a SE2576L chip by Skyworks Solutions. Details about this chip here: http://www.skyworksinc.com/Product/953/SE2576L XQ-02A is a bi-directional signal amplifier module designed for the 2.4GHz band. Features automatic direction (send or receive) identification and switching. According to schematics, maximum output peak power is 2W, but I assume this is not the case of the current PCB. Maybe the voltages must be adjusted, judging by other reports this is doing about 200mW maybe? In my quick testing, connected directly to the TX, the chip is not getting hot, barely warm, so not sure if I need to do something else or the low temperature is maybe of the reduced power output.

i use is on my flysky i6, with a i6b recever. have flown 3.5 km

i use is on my flysky i6, with a i6b recever. have flown 3.5 km

i use is on my flysky i6, with a i6b recever. have flown 3.5 km

This outputs nowhere near 2w as advertised but it does output significantly more than the 100mw that our radios put out as standard and does increase range. In tests I gained about 1/3 extra range from using this. Something to bear in mind is its fragile, if you are going to install inside your radio where it will be protected it will be just fine but I don't recommend external fitting.

This outputs nowhere near 2w as advertised but it does output significantly more than the 100mw that our radios put out as standard and does increase range. In tests I gained about 1/3 extra range from using this. Something to bear in mind is its fragile, if you are going to install inside your radio where it will be protected it will be just fine but I don't recommend external fitting.

This outputs nowhere near 2w as advertised but it does output significantly more than the 100mw that our radios put out as standard and does increase range. In tests I gained about 1/3 extra range from using this. Something to bear in mind is its fragile, if you are going to install inside your radio where it will be protected it will be just fine but I don't recommend external fitting.

доставили со второго раза качество вроде нормальное можно заказывать можно собрать хороший усилитель продавцу спасибо что отозвался на мое сообщение о том что посылки нет и отправил еще раз

доставили со второго раза качество вроде нормальное можно заказывать можно собрать хороший усилитель продавцу спасибо что отозвался на мое сообщение о том что посылки нет и отправил еще раз

доставили со второго раза качество вроде нормальное можно заказывать можно собрать хороший усилитель продавцу спасибо что отозвался на мое сообщение о том что посылки нет и отправил еще раз

Как его использовать без той платы что на фото припаяна?

Как его использовать без той платы что на фото припаяна?

Как его использовать без той платы что на фото припаяна?

very good 4 long Range up to 2 km

very good 4 long Range up to 2 km

very good 4 long Range up to 2 km

von 30mW auf 280mW ist mit 5V Spannung mehr als genug - bei nem Freund sind es sogar 350mW!

von 30mW auf 280mW ist mit 5V Spannung mehr als genug - bei nem Freund sind es sogar 350mW!

von 30mW auf 280mW ist mit 5V Spannung mehr als genug - bei nem Freund sind es sogar 350mW!

ottimo

ottimo

ottimo

prodotto molto valido

prodotto molto valido

prodotto molto valido

Top!

Top!

Top!