Schrijf een beoordeling
  • Alle beoordelingen(599)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(599)
    • 5 Star(571)
    • 4 Star(25)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(2)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (United States)
Toon origineel

Een deel van de recensie is automatisch vertaald.

  • 29/05/2021

    Excellent packaging, except from a little dent on the side the box sustained no damage at all during transit. Everything is packed in a very sturdy box. All the items are protected inside the box by a tailor sized foam inlay. Very very good indeed, packaging leaves nothing to be desired at all. (I wish more products where packed this way, would save a great deal of frustration caused by items getting damaged or broken during transport.) This attention to detail installs confidence in the product as well. I have read many good things about this sensor (it is version 3.1) and hope it performs well for me too. There are many video's out there explaining installation of this sensor on various mainboards so I do not expect any problem. Hopefully this brings me a step closer to that "perfect first layer".

    Toon origineel

    The box was damaged, but thankfully the content was intact. Very, should I say extremely long delivery period ( and that coming from the UK ). Not tested yet.

    Toon origineel
  • 27/03/2021

    Réception sous 10/12 jours. Excellent produit ! Installation relativement simple (sauf si comme moi il y a de la colle à enlever des connectiques de la carte mère), mise à jour du firmware, réglage de l'offset et ajout du G29 dans le slicer (Cura par exemple). Maintenant que tout est bon, j'ai enfin un nivellement du bed correct sur toute la surface !

    Toon origineel
  • 13/02/2021

    was a challenge but got there in the end. fits ender 3 v2 but has an adapter which attached to the LCD ribbon cable port - make sure you follow the wiring diagram and cant go wrong. make sure red cable is to VCC as per diagram.

    Reacties (2)
    Toon origineel
  • 10/01/2021

    Semma product buyed from Tamilnadu, chennai. It tooks 2months to arrive in corona period.

    Toon origineel
  • 08/03/2021

    Worked fine. The ISPUSB cable was really handy to install the new firmware and all the necessary screws were included as well. The process was easy to follow and now is even possible to install other firmware's. The BLTouch is a original one, not a parallel and even came with the zip ties and a extra probe. All in all a very good deal and great improvement for your printer.

    Toon origineel
  • 21/08/2021

    Wasn’t expecting this to be this good due to price and others reviews but I’m so impressed. Packed really well. Easy to install. Do double check the blue/red/yellow wires when you plug them in into the motherboard. I had to swap the pins around on the plug as it was

    Toon origineel
  • 26/11/2020

    il ne manque rien, c'est parfait. j'ai reçu le colis un peu plus tard parce que je l'ai commandé d'Amérique. produit officiel de Creality, en bon état... que dire de plus? c'est parfait!

    Toon origineel
  • 07/05/2021

    The product seems high quality and the shipping from China was faster than expected and without delay in customs. I have not installed yet but have watched several videos on youtube so I am prepared😊

    Toon origineel
  • 04/02/2021

    very good quality, I didn’t expect it to be that good honestly however the guide is very brief, I advise to watch a youtube video on how to install it if you you don’t know

    Toon origineel

    Totaal 0 Pagina's

    Ga naar pagina

    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$21.99
    • US$20.99
    • US$47.99
    • US$206.00
    • US$18.99
    • US$48.99
    • US$4.99
    • US$9.99
    • US$14.99
    • US$7.78
    • US$212.00
    • US$2.09
    • US$259.00
    • US$1.19
    • US$3.99
    • US$319.99
    • US$5.99
    • US$13.99