Klantbeoordelingen

Schrijf een beoordeling
  • Alle beoordelingen(432)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(432)
    • 5 Ster(403)
    • 4 Ster(26)
    • 3 Ster(1)
    • 2 Ster(0)
    • 1 Ster(2)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (United States)
|
Toon origineel

Een deel van de recensie is automatisch vertaald.

  • 26/05/2021

    Much better then original on Ender 3 and Ender 3 v2..Both printing much better. BUT one important thing - better is THIS: https://www.banggood.com/Dual-Gear-Pulley-Dual-Drive-Extruder-Kit-+-3Pcs-MK8-1_75-or-0_4MM-Brass-Nozzle-Accessories-Kit-for-3D-Printer-p-1750567.html?cur_warehouse=CN&rmmds=category

    Reacties (2)
    Toon origineel
  • 01/10/2021

    Nicely machined. Fitted as a replacement onto a different Bowden drive 3D printer. Works better than the original 3D printed part. Need to reverse feed motor direction as filament now enters from opposite side of motor axis. Spring tension is adjustable, remember to adjust e-steps and retraction settings. Very worth the purchase.

    Reacties
    Toon origineel
  • 11/08/2021

    I have installed this on an Ender 3 V2 and it works well. There are no instructions, but you can find instructions on UTube that are very close. I've enclosed a picture of the extruder output, you will notice on the left of the picture under the blue feed handle there is not a brass screw in for the feed tube. Instead this mod uses a black "push in" plastic tube holder. The tube is pushed into the black tube holder and kept in place with the blue clip. Also, there is no washer under the spring loaded feed arm, and when you tighten the screw in the feed arm, it will not bind. Hopefully someone will post complete instructions to install this. If you are mechanically inclined, and view the UTube video, there should be no problem installing this. ADMINISTRATOR: Please note, I tried to upload a .JPG file and it would not work, your site only takes .jpg in lower case - this should be fixed.

    Reacties
    Toon origineel
  • 28/01/2022

    I installed this mod right after I replaced the stock springs with silicone shock absorbers. I have an Ender 3 (version 1), this is compatible with it. I've only done 1 print after these installations. It was a small print (that requires precision) with 3 pieces of the same model installed at the same session. It printed out perfectly! Every 3 pieces printed without glitches! Installing: Don't watch too much Youtube videos. They have many things wrong (but it was a good thing to print the "BV3D Ender 3 Aluminum Extruder Cable Support" before starting the replacement). First, detach the stepper motor cable and bowden tube brass threaded insert. Press the extruder spring release lever a little and remove the screw and the lever with the spring. Also remove the screw that would go into hollow thing inside the spring and put the pieces somewhere and keep them as they were, for reference. Check the brass gear, what is the height in the shaft and keep that in mind. Now you must remove the 3 screws that hold the extruder body (2 round heads and 1 flat one), holding the motor "cube" as it will drop if you don't. Put the pieces aside in the order they were. Also remove the brass gear. Install everything in reverse order (after assembling some items, watch YT), but you can install the brass gear after installing the motor and the body, as you can then align it with the filament holes. Just install it with one screw facing the straight axle side. When installing the lever (compress the spring a little), the lever side (spring) screw must be as "in" as possible and the spring in place and inside the spring this hollow thing and that last screw from the other side to inside the hollow thing that's inside the spring (some YT videos have this really wrong). You can install the Cable Support at the same time but it's impossible to do before you enlarge the hole in the support. Install the black bowden insert and push the tube far in and lock with the blue clip. Then the cable.

    Reacties
    Toon origineel
  • 26/11/2021

    genuine in Creality part. no more issues with the stock chocolate extruder arm! UK 2 day delivery, perfect guys!

    Reacties
    Toon origineel
  • 28/03/2022

    It was very nice experience.. it took only 2 weeks with same product I ordered in good condition. I'll order a lot of products very soon in sha Allah. Thanks banggood.

    Reacties
    Toon origineel
  • 04/02/2022

    Excellent quality product from Creality. I'm very happy

    Reacties
    Toon origineel
  • 01/02/2022

    nagyon jó

    Reacties
    Toon origineel
  • 15/08/2021

    Great upgrade! Filament feeds a lot smoother and it is easier to swap out filaments, no fussing with feeding new filament into extruder. Highly recommended!

    Reacties
    Toon origineel
  • 04/10/2021

    nice build and quality. however the tube connector is built in to the extruder body. not sure how strong the plastic tube fitting is over time.

    Reacties
    Toon origineel
Show:

    Totaal 0 Pagina's

    Ga naar pagina

    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$259.00
    • US$439.99
    • US$2.09
    • US$219.00
    • US$42.99
    • US$2.69
    • US$479.00
    • US$35.99
    • US$389.00
    • US$73.99