Top positieve recensie voor RC speelgoed, leuke sporten, mode, populaire elektronica op Banggood Netherlands|Shoppen Nederlands

81% OFF XXD HW30A 30A Brushless Motor ESC Voor Vliegtuig Quadcopter US$5.00 US$25.59 View It

Algeheel:

crncecivica 24/02/2014

As i sad, these are OK ESC's. If you wanna use them with multirotors, you wanna flash them with simonk's firmware, and make a few modifications on them. Download the source code and edit tgy.inc file. Change .equ F_CPU = 16000000 to .equ F_CPU = 8000000. This ESC's have Atmega8L-8AU which will work on 8 MHz, forget about 16 MHz. Compile the source code with avra.exe, if you are on windows. There is a little bat file on the internet which will help you with that. After compiling, rip of the shrink tube from ESC. Carefully solder some thin wires on the chip, or you can use the flashing tool which can be bought one some other popular site. Add external crystal oscillator to xtal1 and xtal2 pins - 8 MHz with 2x 15 pF to Ground. Look into datasheet for more info. Leads from crystal can be a little longer. We are on 8 Mhz only. After soldering external crystal, you must enable it. Use eXtreme AVR burner for that. Launch the program, configure your programmer. Select Fuse Bits/Settings tab. Down on the left side there is Configure AVR clock icon. Select External Crystal/Ceramic Resonator, frequency range 3.0-8.0 MHz. I had selected Startup time 258CK, i don't know if it makes any difference with other settings. For oscillator option select Limited Swing (for xtal in range 1-8 MHz). Confirm your settings. Select write on low and high fuse. And finally, write fuses on the micro controller. If all goes well, you should have external oscillator running on atmega - at 8MHz. This is now very imune to temperature changes. You ESC will work like a charm. No more weird noises from motors. And don't forget to put some new heat shrink tube on the ESC. Enjoy!

Reacties (4)

Verzenden

nelsonlee Why need to modify this (Change .equ F_CPU = 16000000 to .equ F_CPU = 8000000)? I flashed without changing the code and it work well too.
Beantwoorden 27/02/2014

Verzenden
skiner Do you have green or red color PCB?
Beantwoorden 07/03/2014

Verzenden
crncecivica This atmega is not capable of runing on 16 MHz. If you are still using internal oscillator, it is running on 8 MHz only. If you change to external oscillator, you can use 8 MHz max and then you must change the code. PCB is red.
Beantwoorden 31/03/2014

Verzenden
skipper where can you find the source code.Also, i have the Atmel Atmega Socket Firmware Flashing Tool, but it wont work for me to flash with it. Why not
Beantwoorden 08/10/2014

Verzenden

Ons bedrijf	Neem contact met ons op	Betaling & verzending	Partnership-programma
Over Banggood.com garanties en retourbeleid Algemene voorwaarden Privacybeleid Intellectueel eigendom-claims Sitemap	Neem contact met ons op Nieuwe gebruikergids Help Gespecialiseerde Zaken	Betaalmethodes Verzendgids Locaties waarnaar we verzenden Verwachte levertijd BGpay-instructie	Modebloggers-programma Affiliateprogramma Wholesale-programma Dropshipping Review Club

Ons bedrijf

Neem contact met ons op

Betaling & verzending

Partnership-programma

Over Banggood.com garanties en retourbeleid Algemene voorwaarden Privacybeleid Intellectueel eigendom-claims Sitemap

Neem contact met ons op Nieuwe gebruikergids Help Gespecialiseerde Zaken

Betaalmethodes Verzendgids Locaties waarnaar we verzenden Verwachte levertijd BGpay-instructie

Modebloggers-programma Affiliateprogramma Wholesale-programma Dropshipping Review Club