GirtonTechnology
mijn inhoud
Alle berichten
Beoordelingen
Reacties
antwoorden
vragen

Alle berichten

GirtonTechnology 14/06/2021
Not as described or pictured. smooth reflector. different LEDs. different circuit. IC not soldered just held on by resin. runs rather warm, don't expect it to last long. it is quite bright.
50W Hoog Vermogen 70 LED Overstromingslicht Waterdichte Lodinetungstenlamp Buitentuin AC220-240V
US$14.99 US$17.99
0
aanbevelingen
Reacties (1)
GirtonTechnology 14/06/2021
As described
HCS301 433MHz Rolling Code Afstandsbedieningsschakelaar Draadloos Voeding Relais Ontvanger Module
US$28.99 US$34.99
0
aanbevelingen
Reacties (0)
GirtonTechnology 21/05/2021
have had this a while now, it works quite well apart from not being able to turn the air flow down enough on the hot air gun. Which tends to blow the smaller components around a bit (which most SMDs are). tips are ~4, 6.5, and 9mm I.D. with a fitting I.D. of ~21mm (They fit on other hot air guns we have) For the price it does the job. It is nice and small to have on the bench with both iron and air gun on the one base. The soldering iron does the job well. the stand that comes with it.. well it is thin tin and offers the user no protection from the iron at all, in fact if you don't hook it in the thread then the cord can and does drag it off the table. oh, and be careful unfolding it, it may cut you! pro's it works and is small on the bench. price. simple operation. separate temps for both air and iron. con's iron holder is dangerous. air flow lacks enough adjustment. would I buy another? at this price, yes.
Drillpro 2 in 1 750W 220V/110V Soldeerstation Warmtepistool Verwarmingselement LCD Digitaal Display Soldeerbout Lasstation voor Mobiele telefoon BGA SMD PCB IC Reparatie
US$56.99 US$69.99
0
aanbevelingen
Reacties (0)
GirtonTechnology 10/11/2019
uno is good, screens are a bit ordinary
Geekcreit® UNO R3 Verbeterde versie + 2.8TFT LCD-touchscreen + 2.4TFT Touch Screen Display Module Kit Geekcreit voor Arduino - producten die werken met officiële Arduino-boards
US$24.99 US$34.99
0
aanbevelingen
Reacties (0)
Digitale Schuifmaat LCD Roestvrijstalen Elektronische Liniaal Micrometer Meetinstrument 0-6 inch 150 mm
US$15.89 US$19.07

Q: Is it comming with box or no box ???

gevraagd door Zoki op 2019-02-28 04:05:23

GirtonTechnology comes in a plastic box. but poor quality caliper

2019-04-04 11:57:24 Nuttig (0)
Verzenden
antwoorden (1)
GirtonTechnology 04/04/2019
these work great lots of torque for little current. around 30 mA according to the power supply
DC 6V 1rpm Reversible High Torque Turbo Worm Geared Motor DC motor GW370
US$13.99 US$16.99
0
aanbevelingen
Reacties (0)
GirtonTechnology 26/11/2018
have 2 grub screws and a fair bit of axial play. fine for low speed applications
KFL Zink Legering Kussenblok Flens Kogellager 8/10/12/15/17mm boring Diameter KFL Serie
US$6.99 US$8.99
0
aanbevelingen
Reacties (0)
GirtonTechnology 26/11/2018
bought several of the 1/8" bits (3.175mm) and they cut a hole/groove 4.9mm wide. so closer to 3/16" that is an error of 65% tried a couple to make sure. hopeless
1/4 Inch Rechte Schacht Router Bit Houtbewerkingsfrees 1/2 Fluit Carving Cutter
US$3.00 US$8.99
0
aanbevelingen
Reacties (1)
GirtonTechnology 09/10/2018
This power supply worked for a short while on a 3D printer (same rating as the original) but died after about an hour. Tried 2, same result The blue LED is difficult to see even when they are working. The PCB is floating in the case, just a couple of bits of foam holding it. Couple of wires just cut off left floating. unless you only need a couple of amps don't buy it
19V 4.74A 90W Laptop AC Power Adapter voor ASUS
US$13.99 US$16.99
0
aanbevelingen
Reacties (1)
12V DC 5,5 LB 2,5kg Elektrisch Hefmagneet Elektromagneet Solenoïde Lift Houdmagneet
US$10.99 US$13.99

Q: What is the resistance of the electromagnet?

gevraagd door AllisonKl op 2018-05-17 11:49:43

GirtonTechnology according to the label it is 12v 0.25A which would make it 48R

2018-06-03 07:11:46 Nuttig (0)
Verzenden
antwoorden (3)

Jij bent de expert, kan je helpen?

We nodigen je van harte uit om je te abonneren op de Invite Answer-e-mail!

Als u zich abonneert, nodigen we u uit via e-mail om vragen te beantwoorden die mensen hebben over producten. Door je te abonneren, verdien je ook de "Behulpzame Badge "! U kunt zich op elk moment uitschrijven op de pagina met privacyinstellingen.

Help anderen en wees gelukkiger!

  • Abonneren

Over badges

Badges zijn gerelateerd aan de community en gebruikers verdienen badges door kwaliteitsinhoud te creëren, missies te voltooien of door deel te nemen aan speciale activiteiten. Specifieke mensen hebben ook hun eigen exclusieve badge.
CEO badge

de ceo-badge is alleen in handen van de baas van Banggood.

Badges die je kunt verdienen, komen binnenkort
  • Oké

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • Oké

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe