Deltaking
Q: would this fit a CR10s Pro?
gevraagd door Paulloth21 op 2020-03-27 07:18:06
Deltaking itcould but your print area would be much less pending which CR10s version
2021-08-07 12:44:46 Nuttig (0)Q: son compatibles con la Ender 3 pro?
gevraagd door BG551652501 op 2021-03-03 10:18:12
Deltaking yes
2021-08-07 12:43:10 Nuttig (0)Q: what size filament dose this printer take out of the box?
gevraagd door Supertrowel1 op 2020-10-04 03:59:39
Deltaking 1.75mm
2021-08-07 12:43:01 Nuttig (0)Q: È possibile aggiungere il sensore di filamento? Is it possible to add the filament sensor?
gevraagd door BG533217492 op 2021-02-25 01:29:20
Deltaking Thedevice has extra ports so If you know our firmware well you could add one but would most likely void the warranty as it is a modification you will need to apply to the device
2021-06-08 10:23:02 Nuttig (0)Q: funziona benen con abs ho crea problemi di adesione ?
gevraagd door mask66 op 2018-11-06 11:12:05
Deltaking Itworks well with ABS but using a device like this for ABS it would be best printing during a warm day without the enclosure. If you want to print ABS well an enclosure would be the best bet
2021-06-08 10:21:54 Nuttig (0)
Q: What is the magnet maximum temperature? Is it neodymium or ferrite based magnet? Thanks
gevraagd door TheJ0y op 2018-10-24 08:30:34
Deltaking I found that pushing anywhere above 90 deg on the bed temp the magnet separates from the build track after a while. If you plan to continually print with the heated bed above this temp i would recommend looking at an alternative. (no details on what type of magnet it is but does not seem to lose its charge)
2021-01-17 03:14:53 Nuttig (1)Q: vale para ARTILLERY GENIUS?
gevraagd door titemi op 2020-10-26 06:03:35
Deltaking It will work on any FDM printer with a bed size of 235mm x 235mm or smaller (as long as it doesn't intercept moving parts)
2021-01-17 03:13:00 Nuttig (0)Q: Does it work benen with abs I create adhesion problems?
gevraagd door mask66 op 2018-11-08 11:13:20
Deltaking Itworks well with ABS but when you start to exceed 90 deg on the bed the build track starts to separate from the magnetic bottom
2021-01-17 03:11:13 Nuttig (0)Q: quanti gradi arriva nozzle e ben?
gevraagd door BG571164483 op 2020-05-01 08:46:39
Deltaking yesit's limit is 260 deg, printing for an excessive time at this temp sometimes gives you a temp sensor error. If it does make sure the sensor is mounted correctly in the heater block
2021-01-10 02:16:44 Nuttig (1)
Deltaking Best to check Covid-19 restriction from source country and stock availability
2021-01-10 02:14:14 Nuttig (0)
Deltaking Thereis a leveling sensor. You need to connect it when doing the bed leveling and when leveling is done disconnect it to do the Z0, Z height adjustment and print. the printer does notify you on the panel as a reminder as well in case you forget.
2021-01-10 02:12:38 Nuttig (0)
Q: Will this work with a 4mm glass bed?
gevraagd door Meldrac op 2018-04-03 03:11:52
Deltaking it's only metal tested and confirmed, there is a version for glass
2021-01-02 02:14:48 Nuttig (0)Q: What‘s the weight of the whole plate system?
gevraagd door Mat84 op 2020-06-07 02:22:13
Deltaking it's around 0.4-0.5mm bottom and top
2021-01-02 03:51:18 Nuttig (0)Q: What is the max temperature this can work at without demagnetizing?
gevraagd door Yontash op 2019-02-25 08:47:38
Deltaking been able to push this to 100 deg without demagnetizing the issue is that the mat separates at around 90 deg from the sheet below so a more heat tolerant glue is required then 100 deg is no problem
2021-01-02 03:46:37 Nuttig (0)We nodigen je van harte uit om je te abonneren op de Invite Answer-e-mail!
Als u zich abonneert, nodigen we u uit via e-mail om vragen te beantwoorden die mensen hebben over producten. Door je te abonneren, verdien je ook de "Behulpzame Badge "! U kunt zich op elk moment uitschrijven op de pagina met privacyinstellingen.
Help anderen en wees gelukkiger!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
