Adam
mijn inhoud
Alle berichten
Beoordelingen
Reacties
antwoorden
vragen

Alle berichten

9 Inch/10 Inch 1Din Android 8.0 Auto Stereo Radio Verstelbaar Touchscreen 2 GB + 32 GB GPS Navigatie Wifi AM FM
US$117.89 US$178.99

Q: What is the native LCD resolution?

gevraagd door Adam op 2020-09-11 04:32:12

Andy_19 Once i receive it, i will let you know

2022-01-18 12:46:18 Nuttig (0)
Verzenden
antwoorden (1)
Adam 23/09/2020
Really big insulated enclosure, easy to assemble and seems quite sturdy. Not quite high enough to accomodate a roll of filament on top of the SWX1 but room enough to relocate the filament next to the printer. Great starting point for making a PETG / ABS printing system with the addition of a VOC / Activated carbon filtration system.
Creality 3D® Big Behuizing voor Ender-5/5 pro/5 plus/CR-10Pro/10 V2 3D-printer Aluminiumfolie met Vlamvertragende Behuizing
US$123.99 US$148.99
0
aanbevelingen
Reacties (0)
Adam 23/09/2020
Good package, Mustool have really done a good job of getting cost down to a minimum while still producing a very useful microscope for electronics part identification and soldering. Good: Nice magnification with the lens raised out of the way for soldering. Sharp image on the LCD. Tilt allows reading of stubborn laser etchings on ICs. USB mode allows scope to be used as a webcam on PCs (720p only). Fast realtime image on LCD. Not so good: LCD viewing angles are about what you can expect for the price but fine at 90 degrees (straight ahead). Focus works fine but is a little coarse however the scope height adjustment allows easy fine focus adjustment. Conclusion: For the money I think every $ has gone into the right components to make this the best value scope available in this class. A great addition to any hobby electronics workbench. The larger LCD is useful when doing work and not a gimmick like smaller LCDs we've seen previously.
MUSTOOL G1200 Digitale Microscoop 12MP 7 Inch Groot Kleurenscherm Grote Basis LCD Scherm 1-1200X Continu
US$64.99 US$105.99
0
aanbevelingen
Reacties (0)
Adam 23/09/2020
Fits SWX1 and works fine. No more stressing about a broken idler mid print :)
Titan Aero Aluminium Legering Extruder Spanarm Voor Titan Aero Extruder 1.75mm Prusa i3 MK2 3D Printer Onderdeel
US$10.99 US$13.99
0
aanbevelingen
Reacties (0)
Adam 23/09/2020
Much better than the one that shipped with my SWX1, this one appears to have been injection moulded from multiple points around the plastic gear and is centred properly. The original SWX1 part seems slightly offset causing it to tighten at one point during rotation.
Titan Extruder 66 Tandmodulus 0.5 Roestvrij staal Groot Toestel voor 3D Printer
US$5.99 US$11.99
0
aanbevelingen
Reacties (0)
Adam 23/09/2020
Looks like a decent swap in replacement for the one on my SWX1. Haven't had to use it yet.
Volcano Heet Uiteinde Uitbarsting Verwarming Blok Aluminium Legering Verwarmingsblok Voor 3D Printer
US$5.99 US$7.99
0
aanbevelingen
Reacties (0)
WEICHENSI DQ2-4K156C 15.6 inch 4K draagbare computer gaming monitor touchscreen USB C-display voor tabletlaptop
US$389.99 US$490.16

Q: Does this monitor support HDR?

gevraagd door Adam op 2020-09-10 12:57:40

Shinyvic yes.support hdr.

2020-09-23 05:21:13 Nuttig (0)
Verzenden
antwoorden (2)
Adam 07/08/2018
Paid $5 shipping and received in 12 days, which is not bad. Unfortunately my unit would not read the SD card properly and after searching around for the schematics I was able to remove a faulty mosfet (meant to pull pin 2 low for auto-flashing) which was pulling GPIO2 high somehow. I the whole 'auto-flash' system wasn't working right out of the package and I've had to add some pull-down resistors and a switch to manually enable flashing. This design also has a history of power issues and overheating, has been discontinued by the original designer https://wiki.wemos.cc/products:lolin32:lolin32_pro Not recommended.
Geekcreit® ESP32-WROVER 4MB PSRAM TF-KAART WiFi-module Bluetooth-ontwikkelingsbord
US$18.99 US$22.99
2
aanbevelingen
Reacties (3)

Jij bent de expert, kan je helpen?

We nodigen je van harte uit om je te abonneren op de Invite Answer-e-mail!

Als u zich abonneert, nodigen we u uit via e-mail om vragen te beantwoorden die mensen hebben over producten. Door je te abonneren, verdien je ook de "Behulpzame Badge "! U kunt zich op elk moment uitschrijven op de pagina met privacyinstellingen.

Help anderen en wees gelukkiger!

  • Abonneren

Over badges

Badges zijn gerelateerd aan de community en gebruikers verdienen badges door kwaliteitsinhoud te creëren, missies te voltooien of door deel te nemen aan speciale activiteiten. Specifieke mensen hebben ook hun eigen exclusieve badge.
CEO badge

de ceo-badge is alleen in handen van de baas van Banggood.

Badges die je kunt verdienen, komen binnenkort
  • Oké

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • Oké

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe