Klantbeoordelingen

Schrijf een beoordeling
  • Alle beoordelingen(656)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(656)
    • 5 Star(611)
    • 4 Star(40)
    • 3 Star(3)
    • 2 Star(2)
    • 1 Star(0)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (United States)
|
Toon origineel

Een deel van de recensie is automatisch vertaald.

  • 08/06/2021

    Definitely an upgrade from stock, plastic extruder on Ender 3 V2, those original ones are total crap and break super quickly. It doesn't fit the V2 good out of the box. The inlet connector conflicts wit Z axis lead screw. I had to get rid of it and add a filament guide so the filament isn't scratched by the inlet thread. As other mentioned E steps/mm need recalibration, I had to go from 93 to 138.6 steps. Assembly is pretty straightforward, package came without any instructions though. I advice to use some grease on gears to prevent premature wear. Packaging is very poor, nothing but plastic bags. It's hard to believe nothing was damaged in shipping.

    Reacties
    Toon origineel
  • 23/03/2021

    Great product but was unfortunately missing a piece. Messaged Banggood and had a new part shipped within a few days. Took 16 days from CN to NZ. Works great after adjusting esteps up from 93 to 139.

    Reacties (2)
    Toon origineel
  • 22/01/2021

    good, I’m happy. packaging could of been better. maybe some bubble wrap. item was just placed in zip lock bag and then into shipping bag with no protection and it’s damaged now the paint chipped off.

    Reacties
    Toon origineel
  • 26/09/2021

    Well made extruder. A nice addition to my Ender 3 V2. I recommend this to make sure the filament is properly pushed to the nozzle. Packaging can be better.

    Reacties
    Toon origineel
  • 13/04/2021

    Item arrived in good conditions, no missing parts, packaging was nothing special but doesn’t matter much. So far everything seems solid and nothing broken.

    Reacties
    Toon origineel
  • 29/10/2020

    Very well packaged, installation takes about 30 minutes. If you have Ender 3 Pro, you need to change steps for extruder, from 93 steps (stock extruder) to 139 steps this dual gear extruder. So far I am happy, it works. I bought this dual gear extruder because stock extruder has small slippage with some filaments. Definitely recommended.

    Reacties (1)
    Toon origineel
  • 07/01/2021

    Her boss came peeled off and a little crushed. It can be packaged better. 1 star fell. It came quickly, in full. Turkey has reached my hand with Aras Cargo. I advise.

    Reacties
    Toon origineel
  • 02/09/2021

    As described. Installed on Anycubic i3 Mega S and getting rid of the factory plastic Titan extruder (replica). after installation, e-steps calibration is needed to tune your 3d printer properly. Printing quality improved, minimize under extrusion issues and noise. i totally recommend this extruder!!

    Reacties
    Toon origineel
  • 13/04/2021

    this feeder actually is better than the original one that came with the Ender3. The only problem that I have is that my extruder gear was lil short but I glued it so it’s fine

    Reacties
    Toon origineel
  • 15/01/2021

    Livraison un peu longue mais c'est normal vu les conditions sanitaires. Et il n'y a pas d'instructions de montage mais un petit tuto sur youtube et c'est nickel.

    Reacties
    Toon origineel
Show:

    Totaal 0 Pagina's

    Ga naar pagina

    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$12.99
    • US$6.99
    • US$6.99
    • US$14.99
    • US$8.99
    • US$12.99
    • US$42.99
    • US$12.99
    • US$3.99
    • US$19.99
    • US$15.99
    • US$8.99
    • US$11.99
    • US$11.99
    • US$60.99
    • US$5.99
    • US$107.99
    • US$25.99