Obviously very similar to the other multi modules by Jumper and IrangeX and hopefully will have similar performance. I haven't tried it in anger yet so will have to wait and see. Internally looks to be soundly made with good soldering on a neat board. Antenna lead is soldered directly rather than using a Ipex plug and socket which I feel happier with personally- no chance of cable disconnecting in use. A bootloader is installed so firmware can be updated easily via the mini USB port using the Github firmware repository and instructions. My only gripe would be that it will not fit a standard TGY9x module bay pin connector without the surrounding plastic support being cut away from the bay first. This is not unusual with modules but is a bit of a pain to have to do. Taranis should be fine. This uses a 'universal' module case and the excess holes are covered by the paper label to give a clean outer look. The label is a little large for it's recess so the edges seem to be peeling away a bit. Over time it will probably tend to unstick slowly. No great problem but could do with trimming and sticking again. The mdule case is a good fit in the bay and clips in securely. Overall looks good and should make any Taranis or 9x transmitter into a 'one for all' controller.

Obviously very similar to the other multi modules by Jumper and IrangeX and hopefully will have similar performance. I haven't tried it in anger yet so will have to wait and see. Internally looks to be soundly made with good soldering on a neat board. Antenna lead is soldered directly rather than using a Ipex plug and socket which I feel happier with personally- no chance of cable disconnecting in use. A bootloader is installed so firmware can be updated easily via the mini USB port using the Github firmware repository and instructions. My only gripe would be that it will not fit a standard TGY9x module bay pin connector without the surrounding plastic support being cut away from the bay first. This is not unusual with modules but is a bit of a pain to have to do. Taranis should be fine. This uses a 'universal' module case and the excess holes are covered by the paper label to give a clean outer look. The label is a little large for it's recess so the edges seem to be peeling away a bit. Over time it will probably tend to unstick slowly. No great problem but could do with trimming and sticking again. The mdule case is a good fit in the bay and clips in securely. Overall looks good and should make any Taranis or 9x transmitter into a 'one for all' controller.

Obviously very similar to the other multi modules by Jumper and IrangeX and hopefully will have similar performance. I haven't tried it in anger yet so will have to wait and see. Internally looks to be soundly made with good soldering on a neat board. Antenna lead is soldered directly rather than using a Ipex plug and socket which I feel happier with personally- no chance of cable disconnecting in use. A bootloader is installed so firmware can be updated easily via the mini USB port using the Github firmware repository and instructions. My only gripe would be that it will not fit a standard TGY9x module bay pin connector without the surrounding plastic support being cut away from the bay first. This is not unusual with modules but is a bit of a pain to have to do. Taranis should be fine. This uses a 'universal' module case and the excess holes are covered by the paper label to give a clean outer look. The label is a little large for it's recess so the edges seem to be peeling away a bit. Over time it will probably tend to unstick slowly. No great problem but could do with trimming and sticking again. The mdule case is a good fit in the bay and clips in securely. Overall looks good and should make any Taranis or 9x transmitter into a 'one for all' controller.

Works great in my Taranis X9D Plus ACCST transmitter. Very easy to upgrade to the latest firmware. However, in my Turnigy 9XR Plus the connection pins in the module are too far recessed for proper fit. This results in intermittent power to the module and a very hazardous environment for a Model Plane or Quad. I fixed this problem by removing and placing the module connector on the back side of the PC Card. See Pictures of before and after. Now all is good with my FrSky transmitters and Turnigy transmitters. Rock solid performance.

Works great in my Taranis X9D Plus ACCST transmitter. Very easy to upgrade to the latest firmware. However, in my Turnigy 9XR Plus the connection pins in the module are too far recessed for proper fit. This results in intermittent power to the module and a very hazardous environment for a Model Plane or Quad. I fixed this problem by removing and placing the module connector on the back side of the PC Card. See Pictures of before and after. Now all is good with my FrSky transmitters and Turnigy transmitters. Rock solid performance.

Works great in my Taranis X9D Plus ACCST transmitter. Very easy to upgrade to the latest firmware. However, in my Turnigy 9XR Plus the connection pins in the module are too far recessed for proper fit. This results in intermittent power to the module and a very hazardous environment for a Model Plane or Quad. I fixed this problem by removing and placing the module connector on the back side of the PC Card. See Pictures of before and after. Now all is good with my FrSky transmitters and Turnigy transmitters. Rock solid performance.

the module seems to be ok on working to update the module is very difficult not for beginners. didn't like that was very poor packed just throw it in a yellow bag and that's all, without protection.

the module seems to be ok on working to update the module is very difficult not for beginners. didn't like that was very poor packed just throw it in a yellow bag and that's all, without protection.

the module seems to be ok on working to update the module is very difficult not for beginners. didn't like that was very poor packed just throw it in a yellow bag and that's all, without protection.

Excelent module with easy update procedure. This module doesn't need a programmer module or soldering !!! Just plug the USB cable, download Flash-Multi from https://github.com/benlye/flash-multi, and firmware from https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/releases. I have Taranis X9D+ and I used multi-stm-opentx-taer-inv-v1.3.0.53.bin, but you can chose other one if you don't use TAER configuration. You probably also need to update OpenTX to latest version. With version 2.2.4 I couldn't see multiprotocol selection in my transmitter. It works fine with OpenTX 2.3.5

Excelent module with easy update procedure. This module doesn't need a programmer module or soldering !!! Just plug the USB cable, download Flash-Multi from https://github.com/benlye/flash-multi, and firmware from https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/releases. I have Taranis X9D+ and I used multi-stm-opentx-taer-inv-v1.3.0.53.bin, but you can chose other one if you don't use TAER configuration. You probably also need to update OpenTX to latest version. With version 2.2.4 I couldn't see multiprotocol selection in my transmitter. It works fine with OpenTX 2.3.5

Excelent module with easy update procedure. This module doesn't need a programmer module or soldering !!! Just plug the USB cable, download Flash-Multi from https://github.com/benlye/flash-multi, and firmware from https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/releases. I have Taranis X9D+ and I used multi-stm-opentx-taer-inv-v1.3.0.53.bin, but you can chose other one if you don't use TAER configuration. You probably also need to update OpenTX to latest version. With version 2.2.4 I couldn't see multiprotocol selection in my transmitter. It works fine with OpenTX 2.3.5

Acquistato scontato ad un ottimo prezzo, non l'ho ancora testato perchè sto aspettando la radio.

Acquistato scontato ad un ottimo prezzo, non l'ho ancora testato perchè sto aspettando la radio.

Acquistato scontato ad un ottimo prezzo, non l'ho ancora testato perchè sto aspettando la radio.

Bon module. Le boitier est un peu plus cheap que je pensais mais il est quand même correcte. Il est doté d'un port USB, ce qui permet de mettre assez facilement le module à jour. Il fonctionne correctement avec mes différents récepteurs Frsky, Flysky, futaba et Hubsan.

Bon module. Le boitier est un peu plus cheap que je pensais mais il est quand même correcte. Il est doté d'un port USB, ce qui permet de mettre assez facilement le module à jour. Il fonctionne correctement avec mes différents récepteurs Frsky, Flysky, futaba et Hubsan.

Bon module. Le boitier est un peu plus cheap que je pensais mais il est quand même correcte. Il est doté d'un port USB, ce qui permet de mettre assez facilement le module à jour. Il fonctionne correctement avec mes différents récepteurs Frsky, Flysky, futaba et Hubsan.

Fitted in my radio, it works like a charm due to OpenTx quality. What else ? :-)

Fitted in my radio, it works like a charm due to OpenTx quality. What else ? :-)

Fitted in my radio, it works like a charm due to OpenTx quality. What else ? :-)

Good module

Good module

Good module

Il prodotto è di ottima qualità, ancora non l’ho testato ma alloggia perfettamente nella nuova taranis X9d se 2019. Ha un leggerissimo gioco nell’alloggio della radio ma si può bloccare molto facilmente. Sono molto soddisfatto e consiglio l’acquisto!

Il prodotto è di ottima qualità, ancora non l’ho testato ma alloggia perfettamente nella nuova taranis X9d se 2019. Ha un leggerissimo gioco nell’alloggio della radio ma si può bloccare molto facilmente. Sono molto soddisfatto e consiglio l’acquisto!

Il prodotto è di ottima qualità, ancora non l’ho testato ma alloggia perfettamente nella nuova taranis X9d se 2019. Ha un leggerissimo gioco nell’alloggio della radio ma si può bloccare molto facilmente. Sono molto soddisfatto e consiglio l’acquisto!

Modulo di per se interessante, gestisce molti protocolli grazie ad un firmware open source, il punto è che arriva con un firmware vecchio e l'aggiornamento dalla radio non si può fare, inoltre non è più supportato dal gruppo di sviluppo del firmware

Modulo di per se interessante, gestisce molti protocolli grazie ad un firmware open source, il punto è che arriva con un firmware vecchio e l'aggiornamento dalla radio non si può fare, inoltre non è più supportato dal gruppo di sviluppo del firmware

Modulo di per se interessante, gestisce molti protocolli grazie ad un firmware open source, il punto è che arriva con un firmware vecchio e l'aggiornamento dalla radio non si può fare, inoltre non è più supportato dal gruppo di sviluppo del firmware