Klantbeoordelingen

Schrijf een beoordeling
  • Alle beoordelingen(28)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(28)
    • 5 Star(23)
    • 4 Star(4)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(0)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (United States)
|
Toon origineel

Een deel van de recensie is automatisch vertaald.

  • 21/04/2021

    Envoie rapide ! Elle est monté et fonctionne parfaitement.

    Reacties (1)
    Toon origineel
  • DavidWH
    GB
    25/09/2020

    A very sturdy well made unit. I took my time getting everything right. Those mecano sets and model aircraft of my youth proved their worth. It helps if you like building kits. If you do buy one, mine was very good value, you might get to love or hate the boat nuts. I found a good magnet held on the side of the aluminium pulled the nut into the tightening position, so that was invaluable and you soon get the hang of it. The instructions worked for me, I was methodical, taking the components and screws as needed. The wiring layout is a true test of ingenuity. All just about the right length, none too short. I got them all integrated in the frame. I had some spare blue seal so I cut down the back of 2" lengths and put the cable inside it. A true Rolls Royce of a 3D Printer if you build it right. I am in semi retirement in lockdown, it didn't matter to me that it took most of a week to do it. The example printed right first time.

    Reacties (1)
    Toon origineel
  • 08/11/2020

    After so much time lost with first Tronxy printer sent by BG another one was all good and operational. But if you don't want to do Z offset calibration quite often I suggest to do the upgrade as I did with hot bed support. See the pictures. Without it hot bed tends to bend and even if you do auto leveling it won't help you. With this support, the auto leveling numbers don't exceed 0.2 mm everywhere on the surface of the hot bed. In general printer is quite good but it struggle with printing ABS without enclosure. I have never tried TPU or PETg. Hot bed takes long time to reach 80 Celsius degrees and it seems to be not enough for ABS. I haven't ever achieved more then 85 Celsius degrees. I am going to upgrade it with heated bed silicon pad for 230V AC and more powerful heater for the hot end to. This printer is doing nice without any upgrades with PLA.

    Reacties
    Toon origineel
  • 23/09/2020

    The package is beaten in the transport, I attach verification photographs

    Reacties
    Toon origineel
  • 23/08/2020

    Fast delivery, all ok, well packaged, much more screws then needed. Thank you!

    Reacties
    Toon origineel
  • 07/12/2020

    Sinceramente, siendo propietario de mas de 15 impresoras FDM/SLA he topado con una muy difícil de explicar. El montaje no es nada difícil, pero si es laborioso. La documentación es lo suficiente clara como para no poder quejarse, de hecho esta paso a paso y en cada paso complejo se explica en sub-pasos, documentación correcta y eficiente. La calidad de impresión es muy buena, pero obviamente es algo mas lenta ya que esta limitada por el gran volumen de impresión e infraestructura. En cuanto a la electrónica es algo que no acabo de comprender, ya que no se puede guardar en memoria y cada vez que inicias una impresión el parámetro Z-Offset. Esta impresora para mi solo tiene un único defecto y es que el sensor de nivelación automático esta elevado unos mm por encima de su posición eficiente, lo que nos obliga a corregir el Z-Offset si o si. Sin ser esto el mayor problema tiene una complicación añadida, se ha de calentar la base y la boquilla previamente a calibrar cada vez la impresora, por lo que si no se hace a la primera esta calibración en caliente corres el riesgo de dañar la pegatina adhesiva de la cama protectora. Yo soy usuario avanzado (mas de 6 años en el mundo de la fabricación aditiva) puedo corroborar que hacer cosas a la primera con una maquina que jamás as tocado es muy difícil, por lo que estoy seguro que dañaras si o si la pegatina de adhesión. Yo he conseguido cogerle el truco a la tercera calibración, es decir perfore seriamente hasta llegar al metal de la placa con la boquilla caliente hasta 2 veces antes de saber como reaccionaba este sensor. Estoy estrenando mi impresora ya dañada después de tanto esfuerzo para montarla. Por este precio ruego que se actualice la posición del sensor para futuros clientes, yo mismo estoy dispuesto a comprar alguna mas para añadir en mi granja. Otra cosa y esta si es importante, esta impresora una vez montada es posible que no la puedas pasar por una puerta, cuidado donde la ensambláis si la queréis mover después.

    Reacties
    Toon origineel
  • 09/02/2021

    Quality is good for the money, It prints way betteer than non "pro" version. This is rather a good base for make your own printer. It has good, solid frame. Linear rails are quite good, but need to be cleaned often. The board came with TMS2209 drivers (standalone mode), so the printer is quiet. PSU acrylic case is a joke. The heating-bed does not heats up to 100C. 90C is max after 40 min of waiting. The frame steghtning rods are like joke too. They are have strenght of a paper. Conclusion. Leave the frame, board, maby the PSU and the rails and replace all other parts. But good for the money.

    Reacties
    Toon origineel
  • 09/01/2021

    Unfortunately the firmware is not good on this 3D Printer, an update would be appreciated. The printing bed is big and can only be leveled on the front and back with 3 springs, an additional support underneath the center of the bed would be helpful. The auto leveling seems not to work correctly. It only took only 5 hours to assemble the printer, small objects can be printed immediately but to print big objects (that is what a 500x 500 mm printer is for) we needed 5 days of rebuilding and installing new firmware. It is a good printer for the money but don't buy it if you are new to 3D printing and 3D printers. We have 5 pcs of standard Tronxy X5SA-Pro and they all work perfect.

    Reacties (1)
    Toon origineel
  • 02/07/2021

    Very good seller, the products are as described, fast response and shipment of the items. +++++

    Reacties
    Toon origineel
  • 28/06/2021

    Necesito la factura de este artículo que hemos recibido a Colegio Sagrado Corazón C/ Félix Arano 12 NIF R 3118945 I 31800 Alsasua Navarra

    Reacties
    Toon origineel
Show:

    Totaal 0 Pagina's

    Ga naar pagina

    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$579.00
    • US$399.99
    • US$429.99
    • US$206.00
    • US$449.99
    • US$399.00
    • US$279.99
    • US$199.00
    • US$219.00
    • US$16.99
    • US$3.99
    • US$33.91
    • US$259.00
    • US$199.00
    • US$53.99
    • US$23.99
    • US$499.99
    • US$86.00