Klantbeoordelingen

Schrijf een beoordeling
  • Alle beoordelingen(50)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(50)
    • 5 Star(41)
    • 4 Star(8)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(0)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (United States)
|
Toon origineel

Een deel van de recensie is automatisch vertaald.

  • 25/04/2021

    Recebido em excelente embalagem em tempo record de 3 dias muito antes do previsto. Bom acondicionamento de transportes, excelente apresentação do equipamento, vai ser assemblado e testado nas proximas horas.

    Reacties
    Toon origineel
  • 03/10/2020

    The product itself is very good. There are some points I would like to point out, but considering the price, it is appropriate. However, there is a difficulty in positioning the auto-leveling sensor, which is an important part. The metal sensor used is a product that reacts at 8 mm, but the screw hole that holds the sensor has a gap of 10 mm even if it is adjusted to the bottom. Therefore, there was no choice but to fix the sensor part by a method that does not use screws. I would like you to tell the designers and workers. Move the sensor mounting screw about 3 mm closer to the bed surface.

    Reacties
    Toon origineel
  • 22/06/2021

    https://youtu.be/rQhQyN8Q_Ek

    Reacties (5)
    Toon origineel
  • 23/01/2021

    die Bauanleitung ist für das alte model, aber wenn man eins zu eins überlegt bekommt man es aufgebaut.

    Reacties
    Toon origineel
  • 11/11/2020

    für das Geld ein sehr guter Drucker. Aufbau war gut erklärt (englisch). Man sollte allerdings technisches Verständnis haben. tricky ist der autolevelsensor den sollte man auf Funktion testen und gegebenfalls nachjustieren.

    Reacties
    Toon origineel
  • 01/03/2021

    Sendung bekommen

    Reacties
    Toon origineel
  • 30/07/2021

    Leider musste direkt ein Update der Firmware gemacht werden, da der Druck immer wieder abgebrochen wurde. PC Ducken funktioniert auch nicht wirklich. der Aufbau ist mittel - schwer. Man sollte vorher schon einmal was mit 3D Druck zutun gehabt haben. Das slicing Programm von Tronxy ist nicht ganz so gut. Cura ist deutlich empfehlenswerter. Durch die gute Z- Führung sind die Drucke genau. Auch die riemenbasierten X- und Y-Achsen sind gut gelöst. Das Auto leveling System funktioniert. Alles in allem ein ganz guter Drucker aber nichts für Anfänger.

    Reacties
    Toon origineel
  • 22/06/2021

    mi impresora 3d esta defectuosa , la fuente de alimentacion tiene un sonido irregular tiene fluctuacines en la corriente y empezo a oler a plastico quemado directamente se desenchufo de la corriente electrica y a espera de una respuesta estoy . hoy es la tercera vez que intento comunicarme con vuestra compania sin ninguna respuesta de vuelta creo que es importante ser serios si nos dedicamos a dar un sercio al cliente , hay que ser eficientes y responsables de vuestros errores de fabricacion . saludos gracias

    Reacties (1)
    Toon origineel
  • 22/05/2021

    For this price, it is great, and probably has no same price rivals at all... Sadly there is no longer included the SD card with software, but there are ways to get it online... But you must pay for the card too... All parts are well made, just the filament sensors will not fit, because of nuts collision with the frame, so you must use zip ties instead of screws (because holes are a bit out of line too). But it works well, and there is still the option to make new holes or print new holders, with the right distance, and most importantly, with threads instead of nuts (or you can drill a bit, or print it with the hole, and sink nuts into a holder). Second, and the most important problem is, the sliding rods have no support at ends and are a bit shorter, so if you tighten them, you will deform the frame a bit, and then you never be able to level the bed well. I can level it just around 0.05-0.08mm total differences (most points are pretty close to zero, just the middle of the bed is around +0.05 to +0.08. PS: level the bed fully heated because values will changes after heating ;) ). There are just small and soft washers as a support, but they will deform, and they do not help at all... So be careful while mounting the sliding rods, and do not tighten them more than just a little, or make some end support for the rods. I personally think about printing some holders for the rods, with additional hundredths of mm to push the aluminum profiles back to perfectly straight. Screw rods have some loose too, but it is not a problem of the printer manufacturer, but only a feature of this cheap type of screw rods. You can use ball screw rods instead, but they are a bit expensive... I am thinking about some soft spring, or some weights, which keeps pushing the bed a little down if there will be any problems with prints. But I will try a few prints first :) PS: there are many spare screws (like 30 or more), do not know why, but like it :)

    Reacties
    Toon origineel
  • 11/04/2021

    Great product! the plate self-leveling system and the non-mechanical z-offset are very convenient. the only flaw is the paper manual provided which has the images too small and in some cases I struggled to understand how to mount. luckily there is a pdf manual on the key. For those who use the printer connected via USB: the baud-rate is 115200 and DTS and RTS "Low to High"

    Reacties (1)
    Toon origineel
Show:

    Totaal 0 Pagina's

    Ga naar pagina

    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$299.99
    • US$579.00
    • US$429.99
    • US$279.99
    • US$399.00
    • US$469.99
    • US$929.99
    • US$449.99
    • US$189.99
    • US$559.99
    • US$259.00
    • US$229.99
    • US$8.66
    • US$42.99
    • US$3.99
    • US$206.00
    • US$299.00
    • US$239.99