Klantbeoordelingen

4.73 van5
Schrijf een beoordeling
  • Alle beoordelingen(80)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(80)
    • 5 Star(69)
    • 4 Star(6)
    • 3 Star(1)
    • 2 Star(2)
    • 1 Star(2)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (Netherlands)
  • February-19 2016 08:17:41

    Fonctionne très bien et pas cher, je ne peux pas dire quelque chose à propos de la qualité, mais apres calibrage il semble ok pour moi j'ai souder les fils directement pour gagner du poid ;)

    Reacties
  • July-13 2017 21:59:57

    nice cheap esc, i use it with BE1806 motors on an hexacopter,but if you want to use the full capabilities of this ESC , you must reflash it with Simonk firmware

    Reacties
  • July-27 2017 05:30:03

    spedizione super veloce e prodotto conforme alla descrizione

    Reacties
  • guyVIP2
    FR
    February-11 2018 10:54:09

    produit bien emballé a voir qualité après essais

    Reacties
  • July-17 2017 11:06:27

    Ok

    Reacties
  • June-16 2018 09:01:23

    It arrived in record time. It is nicely made and inexpensive. I just need a Manual now to make it work . My quest begins I fear I hope like hell that it accepts Standard 1ms to 2 ms PWM So far all I get is a lot of bleeping, all of which is meaningful I am sure But without a Manual I am in the hands of the gods

    Reacties (1)
  • March-31 2015 14:56:55

    I ordered 6 of these. As the first review suggested, the tgy-version of the simonK firmware works with these ESCs. You need to change F_CPU to 8000000 since these boards use the internal oscillator. This is no problem with the kkMutlicopter flash tool, since it allows you to build the source. These ESCs get very warm. At roughly 5 amps the P-fets started burning my fingers. Lowering the PWM frequency to 8kHz helped somewhat. The stock FW uses 7.8kHz PWM (verified with scope). The quality is ok,

    Reacties
  • August-26 2018 05:08:42

    please help connected all up. everything works except for the motor. just makes continued biep biep biep biep. I switched wires around in every possible way. Same result Everytime. thanks.

    Reacties
  • October-24 2014 19:59:58

    These can be flashed with Simonk. You need an 8MHz build of tgy.hex. These have no external oscillator. The hardware is fairly low quality, but given the price they're more than adequate. P-CH FETs are TPC8111, and N-CH are IRF7832

    Reacties
  • February-11 2015 00:55:14

    За эту цену неплохие регуляторы. Брал 6 штук - 4 на коптер и 2 в запас. Работают все. Прошил Simonk TGY через kkMulticopterFlashTool. В качестве ISP программатора использовал Arduino Uno.

    Reacties
Show:

    Total 0 pages

    Go to page

    Go

    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$9.66
    • US$10.29
    • US$6.76
    • US$5.97
    • US$6.51
    • US$11.99
    • US$8.89
    • US$14.88
    • US$14.90
    • US$10.82
    • US$40.99
    • US$35.99
    • US$20.99
    • US$68.59
    • US$38.99
    • US$69.99
    • US$10.55
    • US$15.99