Klantbeoordelingen

Schrijf een beoordeling
  • Alle beoordelingen(62)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(62)
    • 5 Ster(57)
    • 4 Ster(1)
    • 3 Ster(1)
    • 2 Ster(2)
    • 1 Ster(1)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (United States)
|
Toon origineel

Een deel van de recensie is automatisch vertaald.

  • 19/04/2017

    The encoder is very small, should fit on most quadcopter builds 180mm or bigger with ease. I have not actually tested it yet but i fully expect there to be zero issues. Seems very good quality.

    Reacties
    Toon origineel
  • 13/10/2016

    I bought this and was thinking it would fit into this product http://www.banggood.com/Pixhawk-PX4-2_4_8-Flight-Controller-32-Bit-ARM-PX4FMU-PX4IO-Combo-for-Multicopters-p-1040416.html?rmmds=search and thinking that it would fit into the RCIN section. it doesn't. I'm guessing I'm gonna have to make my cables somehow. On the picture it can fit into a pixracer. So, either remove the word pixhawk in the name or provide a cable is your best option.

    Reacties
    Toon origineel
  • 24/08/2018

    How to save wiring you can multiplex with PPM 8 channel Input 3pin Output 5V power Supply Fast Delivery by BG

    Reacties
    Toon origineel
  • 22/02/2017

    ideal to convert any PWM receiver to output a PPM signal. very small board, nice for DIY projects...

    Reacties
    Toon origineel
  • 27/11/2016

    Конвертер конвертирует PWM сигнал в PPM. Использовано на приёмнике Корона с Naze32. Сигнал запаздывает, есть задержка в пол секунды.

    Reacties
    Toon origineel
  • Reman
    GB
    16/07/2017

    After upgrading the FC on one of my hexacopters I realised that the new one was PPM only. I couldn't find a way to get a camera gimbal to work from FC outputs, So I was stuck. Then I saw these. This allows me to convert 8 of my 10 channels into PPM and still use the last 2 as PWM for the servos. I was worried that this might cause lag in the PPM output, But after a little play with this, I've come to the conclusion that this converter works so close to instantly that I can't tell it's in the loop. I cut the original Pixhawk output plug off and crimped on a servo plug for the F3 I'm using. It took next to no setup (Just tell the TX to output PWM and the converter does the rest). So, If you need a mix of PPM and PWM outputs, Then this is a great option.

    Reacties
    Toon origineel
  • 29/05/2017

    converts pwm to ppm signal allowing me to use an outdated radio and receiver with all the new flight controllers

    Reacties
    Toon origineel
  • Reman
    GB
    05/03/2017

    After upgrading the FC on one of my hexacopters I realised that the new one was PPM only. I couldn't find a way to get a servo pan and tilt camera platform to work from FC outputs, So I was stuck. Then I saw these. This allows me to convert 8 of my 10 channels into PPM and still use the last 2 as PWM for the servos. I was worried that this might cause lag in the PPM output, But after a little play with this, I've come to the conclusion that this converter works so close to instantly that I can't tell it's in the loop. I cut the original Pixhawk output plug off and crimped on a servo plug for the F3 I'm using. It took next to no setup (Just tell the TX to output PWM and the converter does the rest). So, If you need a mix of PPM and PWM outputs, Then this is a great option.

    Reacties
    Toon origineel
  • 03/01/2017

    très satisfait

    Reacties
    Toon origineel
  • 26/10/2016

    not very expensive and its mich smaller than i expected which is a good thing! it does its job so im happy

    Reacties
    Toon origineel
Show:

    Totaal 0 Pagina's

    Ga naar pagina

    recommendation for you
    • US$24.99
    • US$3.99
    • US$11.99
    • US$8.00
    • US$23.99
    • US$66.99
    • US$11.99
    • US$16.99
    • US$25.99
    • US$39.99
    • US$33.50
    • US$57.99
    • US$66.49
    • US$79.99
    • US$16.99
    • US$76.99
    • US$17.99
    • US$49.99