Klantbeoordelingen

Schrijf een beoordeling
  • Alle beoordelingen(118)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(118)
    • 5 Star(105)
    • 4 Star(11)
    • 3 Star(0)
    • 2 Star(1)
    • 1 Star(1)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (United States)
|
Toon origineel

Een deel van de recensie is automatisch vertaald.

  • 07/07/2021

    Vraiment pratique et très fonctionnel fonctionne en Fr et en Wifi s'intègre bien dans une installation domotique aucun changement a prévoir marche sans fil neutre il suffit juste de placer la capacitance entre les deux fils n'importe qui peut l'installer tellement que c'est facile n'oublier pas de couper le courant avant.

    Reacties
    Toon origineel
  • 11/05/2021

    A csomagolás lehetett volna jobb, de túlélte a szállítást. Címre kértem, de átvételi pontra érkezett ez nem könnyítette meg az átvételt. A készülék egyenlőre jól működik. Könnyen dolgozik együtt a Google Assistanttal.

    Reacties
    Toon origineel
  • 06/09/2021

    Très bon produit je recommande je commence a l'installer petit à petit dans toute la maison très facile à installer et a utiliser.

    Reacties
    Toon origineel
  • 05/05/2021

    Thanks.Arrived safely.

    Reacties
    Toon origineel
  • 31/10/2021

    Worked for only 10 minutes and then completely died. I don't recommend to buy it.

    Reacties
    Toon origineel
  • 08/04/2020

    Got a different pcb than the previous comment that showed the different pads to solder to flash the firmware. I could easily flash the switch with the rx/tx/gpio0 pins accessible at the front and 5V power via the pins already present at the back. Used the same esphome config as a sonoff touch wall switch. Switch works perfectly.

    Reacties (1)
    Toon origineel
  • 05/02/2020

    It works as described. You need to put capacitor in parallel with the lamp as described. It works also with my google home mini, so I can control it with voice. :-)

    Reacties
    Toon origineel
  • 10/03/2020

    Good product. I could install Tasmota on it. You need to connect to the pads above the chipset. The pinout is from left to right TX, RX, GND, VCC, GPIO0 (see picture attached). When you power on the device you need to connect GPIO0 to GND in order to start the programming mode. I selected "Sonoff Dual R2" in the Tasmota configuration and I see that it works without issues.

    Reacties (1)
    Toon origineel
  • 22/02/2020

    Works very good with ESPHome (just took some effort to flash as pins are not marked). Very silent and responsive. Capacitor really small compared to T4 one. Two of them doesn't fit in normal JB setup.

    Reacties (1)
    Toon origineel
  • 29/07/2020

    These work really well. Flashable with Tasmota. Just be careful of the pads for the headers, the solder can easily come off when removing the link cables. Best to use a solder pump and very little pressure.

    Reacties
    Toon origineel
Show:

    Totaal 0 Pagina's

    Ga naar pagina

    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$9.99
    • US$18.99
    • US$35.14
    • US$28.99
    • US$21.99
    • US$17.35
    • US$28.24
    • US$13.99
    • US$19.99
    • US$17.99
    • US$8.99
    • US$21.99
    • US$11.99
    • US$20.99
    • US$16.99
    • US$21.99
    • US$28.99
    • US$12.99