Klantbeoordelingen

Schrijf een beoordeling
  • Alle beoordelingen(94)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(94)
    • 5 Star(88)
    • 4 Star(5)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(0)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (United States)
|
Toon origineel

Een deel van de recensie is automatisch vertaald.

  • AKADAP
    US
    24/09/2021

    I bought both the 1-6mm set and the 6-10mm set. At the time I ordered this, both the 1-6mm kit and the 6-10mm kit had the same part number and description. I got the correct kits in spite of this confusion. This is an OK set of metric drills. The 1.1 mm drill in my set is a bit short making it a bit difficult to grab. The wire that lifts the drill index out of the large bit case tends to bend the thin sheet metal of the drill case making it very difficult to remove the 9.2 and 9.4mm drills. Only drills 3mm-10mm are split point, the smaller drills are just normally sharpened. A few of the drills do not have the split point done very well. At least one drill was not ground enough to sharpen the entire cutting edge. The advertising copy on these sets do not indicate the accuracy of the diameter of these drills, so I measured all of them. They are all slightly under sized with a median error of -0.04 mm The minimum error was -0.005mm and the maximum error was -0.08mm This was the first metric set that I have found that covers the range 1 to 10 mm in 0.1mm steps. I was continually having to use numbered drills to approximate the correct drill size for metric taps. Most metric kits I've seen do 1mm or 0.5mm steps, this kit allows me to directly grab the correct size drill. This kit does not wow me with quality, but it also does not horrify me with the price. It is a reasonable price/quality tradeoff. This kit will serve the purpose I have for it.

    Reacties
    Toon origineel
  • 12/04/2021

    barang sudah sampai

    Reacties
    Toon origineel
  • 13/01/2021

    One of the drills(4,7mm)was to long so that it damage the interior. The case was broken by the tab and has a dent. In my opinions the handling was not very careful. The damage was not made by the DHL because the case was fixed by a foil and the danages were under the foil.

    Reacties
    Toon origineel
  • 16/12/2020

    ok thank you

    Reacties
    Toon origineel
  • 21/09/2021

    its really hssco! good quality!

    Reacties
    Toon origineel
  • 04/02/2021

    Vypadají kvalitně.Uvidíme jak se zachovají při vrtání do nerezu.They look very good.

    Reacties
    Toon origineel
  • 29/12/2020

    salve, sembrano di buona qualità, ancora non provate.Saluti.

    Reacties
    Toon origineel
  • 07/09/2021

    Good quality drill bits in a sturdy tin.

    Reacties
    Toon origineel
  • 05/03/2021

    Finally filling in the gaps between every 0.5 mm step. The drills I have used so far are very sharp and a joy to work with. Wonderful set in a sturdy metal case. I only wish that the complementing set -up to 10 mm- was less expensive as it is, an attractive price (like these) would definitely make me buy them. This is a beautiful set and I am very happy with them. Thank you Banggood!

    Reacties
    Toon origineel
  • 09/01/2021

    Appear to be a good set of drills. Drills are all very close to the stated size. The grind looks good on all the drills I checked. They are split point on 3.0 mm and above. In the small amount of use so far they cut very well. Only issue I have with them is the box they come in is a bit cheap - e.g. it is not easy to get the drills from the back positions in the two front rows without removing a drill in front first. Still I am very happy with the product.

    Reacties
    Toon origineel
Show:

    Totaal 0 Pagina's

    Ga naar pagina

    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$7.59
    • US$16.99
    • US$5.99
    • US$21.99
    • US$22.99
    • US$4.99
    • US$29.99
    • US$7.59
    • US$9.99
    • US$14.99