excellent receiver , once flashed with new firmware Flashing details:- http://www.banggood.com/USBASP-USBISP-3_3-5V-AVR-Downloader-Programmer-With-ATMEGA8-ATMEGA128-p-934425.html http://www.rcgroups.com/forums/showpost.php?p=32959023&postcount=1147 http://www.rcgroups.com/forums/showpost.php?p=32382264&postcount=864 CH5-MOSI CH6-MISO CH7-SCK VCC GND RESET ( attach before plugging in usbasp) Programable fail-safe (PFS) and binding of RX-F802:- 1) Press bind button on RX and power it up , release button . Led will stay on 2) Turn on Taranis :- press menu button and then page button . Scroll down and set mode=d8 and channel range =Ch1-8. Then enter bind . 3) RX led will go off 4) Arrange sticks for your preferred fail safe 5) Press ENT button on Taranis to exit bind 6) RX will flash 7) Remove power to receiver and re- connect , it should come on with a solid led 8) Your done , receiver bound and fail-safe set PPM out:- connect channels 1+3 , PPM out will be on channel 4 Sbus out:- Connect channels 5+7 . Sbus is on tx pad under rx cover next to Ariel RSSI ( signal strength) :- RSSI is output on Channel 5 when in SBUS or PPM mode for most firmwares. It can be put on channel 9 when the cleanflight software is loaded For MWOSD the min rssi should be set to 33 and the max to 100

excellent receiver , once flashed with new firmware Flashing details:- http://www.banggood.com/USBASP-USBISP-3_3-5V-AVR-Downloader-Programmer-With-ATMEGA8-ATMEGA128-p-934425.html http://www.rcgroups.com/forums/showpost.php?p=32959023&postcount=1147 http://www.rcgroups.com/forums/showpost.php?p=32382264&postcount=864 CH5-MOSI CH6-MISO CH7-SCK VCC GND RESET ( attach before plugging in usbasp) Programable fail-safe (PFS) and binding of RX-F802:- 1) Press bind button on RX and power it up , release button . Led will stay on 2) Turn on Taranis :- press menu button and then page button . Scroll down and set mode=d8 and channel range =Ch1-8. Then enter bind . 3) RX led will go off 4) Arrange sticks for your preferred fail safe 5) Press ENT button on Taranis to exit bind 6) RX will flash 7) Remove power to receiver and re- connect , it should come on with a solid led 8) Your done , receiver bound and fail-safe set PPM out:- connect channels 1+3 , PPM out will be on channel 4 Sbus out:- Connect channels 5+7 . Sbus is on tx pad under rx cover next to Ariel RSSI ( signal strength) :- RSSI is output on Channel 5 when in SBUS or PPM mode for most firmwares. It can be put on channel 9 when the cleanflight software is loaded For MWOSD the min rssi should be set to 33 and the max to 100

excellent receiver , once flashed with new firmware Flashing details:- http://www.banggood.com/USBASP-USBISP-3_3-5V-AVR-Downloader-Programmer-With-ATMEGA8-ATMEGA128-p-934425.html http://www.rcgroups.com/forums/showpost.php?p=32959023&postcount=1147 http://www.rcgroups.com/forums/showpost.php?p=32382264&postcount=864 CH5-MOSI CH6-MISO CH7-SCK VCC GND RESET ( attach before plugging in usbasp) Programable fail-safe (PFS) and binding of RX-F802:- 1) Press bind button on RX and power it up , release button . Led will stay on 2) Turn on Taranis :- press menu button and then page button . Scroll down and set mode=d8 and channel range =Ch1-8. Then enter bind . 3) RX led will go off 4) Arrange sticks for your preferred fail safe 5) Press ENT button on Taranis to exit bind 6) RX will flash 7) Remove power to receiver and re- connect , it should come on with a solid led 8) Your done , receiver bound and fail-safe set PPM out:- connect channels 1+3 , PPM out will be on channel 4 Sbus out:- Connect channels 5+7 . Sbus is on tx pad under rx cover next to Ariel RSSI ( signal strength) :- RSSI is output on Channel 5 when in SBUS or PPM mode for most firmwares. It can be put on channel 9 when the cleanflight software is loaded For MWOSD the min rssi should be set to 33 and the max to 100

Nice little rx, lightweight, small, e.g. half height of a R615X. Hence this one will fit even on small frame. For the A1&A2 ports, it comes with two bread board cables. The antenna is a dipole antenna, but I am wondering why most Chinese builders of that stuff stay below 1/4 wave for the length on the active part.. After I have done the mod on the 7e for this rx, I will report how the telemetry works.

Nice little rx, lightweight, small, e.g. half height of a R615X. Hence this one will fit even on small frame. For the A1&A2 ports, it comes with two bread board cables. The antenna is a dipole antenna, but I am wondering why most Chinese builders of that stuff stay below 1/4 wave for the length on the active part.. After I have done the mod on the 7e for this rx, I will report how the telemetry works.

Nice little rx, lightweight, small, e.g. half height of a R615X. Hence this one will fit even on small frame. For the A1&A2 ports, it comes with two bread board cables. The antenna is a dipole antenna, but I am wondering why most Chinese builders of that stuff stay below 1/4 wave for the length on the active part.. After I have done the mod on the 7e for this rx, I will report how the telemetry works.