Klantbeoordelingen

Schrijf een beoordeling
  • Alle beoordelingen(23)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(23)
    • 5 Star(18)
    • 4 Star(2)
    • 3 Star(2)
    • 2 Star(1)
    • 1 Star(0)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (United States)
|
Toon origineel

Een deel van de recensie is automatisch vertaald.

  • 30/08/2021

    This kit comes complete with almost everything you need to make it work on an ender 3 V2. There are two issues with the kit as supplied. 1) for the V2 the hot end shroud doesn't work with the included bracket. The included bracket is for the Ender 3 regular printer not the V2. I had to fabricate a bracket from my old bracket and the belt slots don't line up right. 2) the m3x8 screws for the bearing blocks are too long and they should be m3x6 for x and 1 z axis, but are okay for y and motor side z axis. There are NO way instructions so figuring it all out is hard. There are a few YouTube videos that help if you get lost. Overall I'm happy with the kit and it's an upgrade, but not complete as shipped. The BLtouch is a nice bonus for the price!!!!

    Reacties (1)
    Toon origineel
  • 22/04/2021

    good kit,need little brain ro put it together

    Reacties (4)
    Toon origineel
  • 14/07/2021

    poorly packed and guide rails missing the small cap to stop the carage from falling of the rails.

    Reacties (1)
    Toon origineel
  • 24/07/2021

    Seems great!

    Reacties
    Toon origineel
  • 08/09/2021

    package extremly poor, lineals rods out of the guides, no foam or any to protect the items

    Reacties
    Toon origineel
  • 09/02/2021

    Caution! This kit is for an Ender 3 Pro only, i.e. make sure your Y axis is on a 40x40mm profile. It can be adapted to the other Ender 3 models with the 20x40mm Y axis, but it requires drilling new holes to the Y carriage and 3D printing the Y axis ends. The product itself is very well built, it takes some time to get it assembled properly. I had the Z axis binding after assembly. After loosening the Z extrusions at the top and bottom, then tightening them back up again, everything was fine.

    Reacties (1)
    Toon origineel
  • 18/03/2021

    No instructions, the right Z axis bracket was mirrored so the X axis was limited by 2cm because the printer head was hit by the bracket. I have a swiss direct drive so the motor get stuck by the bracket.

    Reacties
    Toon origineel
  • 04/01/2021

    Sinceraly I don´t like, because where is the manual to help in the assemblyjQuery111306169553782189643_1609800210291?

    Reacties
    Toon origineel
  • 06/07/2021

    Do Polski z Czech w 4 dni robocze, także dokładnie jak w opisie. Wysyłka Inpost. Z zamówieniem wszystko ok.

    Reacties
    Toon origineel
  • 28/06/2021

    ottimo kit per aggiornare la stampante Ender 3. Adesso posso stampare con velocità maggiore e mantenendo una precisione davvero ottima

    Reacties
    Toon origineel
Show:

    Totaal 0 Pagina's

    Ga naar pagina

    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$3.99
    • US$259.00
    • US$1.99
    • US$33.91
    • US$186.00
    • US$199.00
    • US$196.00
    • US$2.09
    • US$3.29
    • US$239.00