4.94 van5
Schrijf een beoordeling
  • Alle beoordelingen(472)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(472)
    • 5 Star(444)
    • 4 Star(26)
    • 3 Star(2)
    • 2 Star(0)
    • 1 Star(0)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (Netherlands)
  • November-13 2020 14:50:42

    Received extruder today,everything is well packed and nothing broken. Was a bit tricky installation on my CR-10 V3,had to print new mount for BMG from thingiverse,also i had to swap wires on extruder stepper motor to make it inverted to work like it should. But on the end i got alot quieter extruder without annoying click-clack sounds as E3D stock extruder was. A bit slower shippment,but overall im satiafied with the product. Recommended seller,will buy in future spare parts from your store! 😊

  • June-25 2020 01:39:50

    Упаковано в пластиковый футляр. В комплекте инструкция в картинках и пара качественных ключей шестигранников. Пластик литой. На прижимной шестерне игольчатый подшипник. Главная шестерня посажена на подшипники. На шестернях лёгкая заусня, не критично. Колдэнд e3d v6 зажимает хорошо, без люфтов. На prusa i3 он ставится в режиме боуден-экструдера. Как не крути, а для использования в качестве директ-экструдера надо рисовать либо новую каретку, либо крепление, либо перепечатывать корпус. Пластик хватает уверенно, даже PET домашнего изготовления.

  • April-14 2020 17:20:26

    Arrived earlier than expected, all well protected inside a plastic box with sealed plastic bags inside. The extruder comes with everything you need to install it, including the screws and Allen keys. I installed it on my Ender 2 and so far everything seems great. I'll update the review later after more testing

  • March-29 2020 15:58:56

    Considerato il prezzo molto basso funziona decisamente bene. Il montaggio è facile e sulla mia geeetech a20 non richiede ne l'adattatore ne l'inversione del motore. La struttura è abbastanza robusta con l'eccezione della levetta di sblocco che sembra molto fragile, vedremo quanto durerà. Per fortuna il cambio filamento si può fare senza doverla azionare.

  • December-16 2020 06:53:56

    Installed it on my Prusa i3 MK2 clone using this adapter: https://www.thingiverse.com/thing:3206085. The print quality has dramatically improved compared, the only problem is that ejecting the filament from the printer menu does't work, because of the too high speed and high E-steps in the firmware. Not a huge problem though. The second one I bought is going to my Kingroon KP3 printer soon.

  • October-09 2020 10:10:24

    Excelente acabado. Cumple con las expectativas de la publicación. Todo muy bien protegido en su caja plástica. Recomendado

  • July-09 2020 13:25:12

    Super easy to install on Ender 3. No additional hardware needed. I had to change e-step to 414 in order for it to be accurate. Overall it works great and I would recommend it as an upgrade over stock extruder.

  • May-03 2020 12:49:18

    es claro que no es el original, pero se siente rígido aún no lo instalo por que estoy esperando otras piezas pero si se siente de buena calidad

  • September-08 2020 16:00:39

    El producto viene completo y funciona bien, pero la caja del producto venia rota y abierta, podría haber traído algo más de protección el paquete.

  • August-09 2020 03:27:08

    Very nice packed. Replaced the Geeetech A10M ones. This one is much much better. No more gear signs on the filament, that means you can do much many retractions on the same area of the filament.


    Total 0 pages

    Go to page


    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$2.57
    • US$13.48
    • US$3.74
    • US$15.99
    • US$6.99
    • US$4.69
    • US$2.59
    • US$14.66
    • US$9.48
    • US$2.40
    • US$17.49
    • US$8.42
    • US$4.99
    • US$42.86
    • US$10.40
    • US$10.58
    • US$24.99
    • US$3.29