Klantbeoordelingen

5 van5
Schrijf een beoordeling
  • Alle beoordelingen(26)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(26)
    • 5 Star(26)
    • 4 Star(0)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (Netherlands)
  • August-07 2017 10:57:07

    Worked fine in plastics with 5mm DOC with about 1800 rpm (280m/min) and a feedrate of 1200 mm/min (0.15 mm per teeth). Tried Steel (S235JR) with 1600 rpm (250m/min) and 800 mm/min feed (0.125 mm per teeth) and it cut well with a 4 mm DOC Havent tried bigger cuts (Hoffman says 1604 should be good up to 7mm DOC) or stainless yet but so far I really can't complain

    Reacties
  • September-12 2018 01:39:48

    Good machining head, inserts fit great on it , good balance on it for the money!

    Reacties
  • October-31 2020 04:48:37

    Ottimo oggetto, molto ben fatto molto robusto, consigliatissimo.

    Reacties
  • ivoVIP4
    EE
    November-11 2019 11:44:19

    seems good for workshop use, on closer inspection noticed a few small dings on corners under the insert seats, that needed to be stoned off, but that's ok at this price point.

    Reacties
  • October-08 2019 02:05:27

    Ottimo prodotto, accoppiamenti perfetti degli inserti, discreta lavorazione delle facce, segnalo sostituzione in garanzia per difetto della prima spedizione, molto celere l'assistenza nella risposta e nella risoluzione del problema.

    Reacties
  • February-22 2018 16:26:03

    This is my first carbide end mill but have used sherwood etc HSS mills as well as cheap chinese ones in the past. The price for this is cheap but it mills aluminium, carbon fibre and steel beautifully with a far better surface finish than any HSS mill I have used - 100% recomended.

    Reacties
  • March-13 2017 12:28:35

    I bought two of these at different times and have been using them regularly. They work really well and stand up to heavy use.

    Reacties
  • September-02 2016 12:46:01

    I am very happy with this face mill. It cuts good and give a very nice finish. I told several friend about it

    Reacties
  • March-21 2018 10:09:30

    Всё отлично дошло быстро товар отличного качества

    Reacties
  • July-11 2016 10:17:27

    На вид качественный товар. В работе пока не использовалась.

    Reacties
Show:

    Total 0 pages

    Go to page

    Go

    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$76.44
    • US$16.19
    • US$124.82
    • US$28.52
    • US$21.92
    • US$59.01
    • US$48.66
    • US$28.68
    • US$30.28
    • US$27.51
    • US$8.50
    • US$20.45
    • US$18.51
    • US$89.99
    • US$56.11
    • US$7.41
    • US$44.52
    • US$21.99