4.95 van5
Schrijf een beoordeling
  • Alle beoordelingen(85)
  • Afbeeldingen
  • Videos
  • Ster
    • Ster(85)
    • 5 Star(82)
    • 4 Star(2)
    • 3 Star(1)
    • 2 Star(0)
    • 1 Star(0)
Sorteren op:
Top recensie
  • Top recensie
  • Meest nuttig
  • meest recent
Recensies alleen uit uw land (Netherlands)
  • February-17 2020 23:40:47

    Love it

  • May-25 2017 03:36:14

    Delivered in 8 days to Australia using priority direct. Excellent addition to ANET A8. Adheres neatly to the underside of the standard A8 aluminium bed. Using this heating element in place of the original MK2 bed element, the temperature reaches 110˚c in under 10 minutes. Current @ 12V: 15.8A @ 15˚c, 14.8A @ 50˚C, 14A @ 90˚C, 13.7A @ 110˚c. I have not tested the incorporated thermocouple- I am still using the one attached to the aluminium bed. 12v power supply in use: MeanWell NES-350-12

    Reacties (2)
  • October-25 2017 16:19:22

    Старый подогреватель грел до 100С за 15 минут в среднем и потреблял около 150Вт. Этот до 100С поднимает за 7 минут при 220Вт. Пришлось поменять штатный блок питания на 360Вт. Рекомендую!

  • November-22 2017 06:06:44

    Okay so the packing was not good at all. It would be nice if there was a bubble wrap just to protect the surface. The Thermistor is not included with the 2 pin connector. It was difficult to connect them. The heating pad works great. Takes less than 2 min to heat up to 100 degree Celsius

  • January-07 2019 04:51:39

    I use it to heat the house of my dog, controlled by a sonof basic, +BME280 and nodemcu custom fw. It can generate about 8-10 C difference, compare to the outside temperature. It needs about a 12V/15A PS, and worms up in a minute. I do recommend it to use not just for its purpose, you can heat small cabinets, of avoid freezing the drinking water for you favorite dog :-)

  • June-04 2019 09:25:15

    WOW, very fast heating. With 12v in 2 Minutes on 75°C. Accurate sensor. 12v wires does not get warm if the mat heating. I am Happy with this. Thank you.

  • February-21 2018 04:48:33

    Silicone heating pad, I attached with the provided adesive to my Aluminum 4mm thick bed of my prusa i3. Attached to an external mosfet wired up to ramps, it could heat up 100° degrees in less than 10 minutes, as can be seen from the octopi screenshot.

  • March-13 2018 06:58:50

    resistance is 0.8 ohm and it sucks 15A at 12V so around 180W heating capacity.

  • September-13 2017 19:09:03

    muy buen producto para la cama caliente de mi impresora 3d H-bot

  • February-16 2018 15:03:15

    Ottimo per il piatto della stampante 3D si riscalda velocemente e raggiunge temperature elevate.


    Total 0 pages

    Go to page


    Wellicht ben je ook geïnteresseerd in

    recommendation for you
    • US$8.14
    • US$14.99
    • US$16.99
    • US$17.84
    • US$11.59
    • US$17.95
    • US$4.23
    • US$12.49
    • US$33.81
    • US$14.99
    • US$13.37
    • US$13.85
    • US$8.67
    • US$6.99
    • US$21.00
    • US$10.38
    • US$10.60
    • US$13.99